What is the relationship between cold-rolled coil width and utilization rate?

Mar 12, 2026 Leave a message

1.What is the utilization rate of cold-rolled coils? How does width affect it?

The utilization rate of cold-rolled coils typically refers to the percentage of the total area of ​​the final finished parts to the total area of ​​the cold-rolled coil consumed. Width is one of the most critical geometric parameters affecting utilization rate, primarily through the following mechanisms:

Edge Removal Loss: Cold-rolled coils have two edges (usually 5-20mm each). These edges, due to edge cracks or uneven thickness, need to be removed during slitting or shearing, becoming scrap. If the required finished product width can fully utilize the removed middle portion, waste is minimized.

Layout Economy: During blanking (stamping or slitting), multiple parts need to be arranged across the width of the coil. If the width allows for the arrangement of parts in multiples of each other with minimal gaps, the utilization rate is high; conversely, if the width results in a wide, unusable strip of material after arrangement, the utilization rate decreases.

cold-rolled coil

2.Why is "width excess material" considered the biggest contributor to utilization loss?

Fixed Loss: Assuming a part needs to be 100mm wide, placing two of them would require 200mm. Adding shearing clearance and edge trimming, a 215mm wide steel coil might be needed. The extra 15mm is the width surplus (including edge trimmings).

Marginal Loss: For narrow strips, every 1mm increase in width can mean an extra piece of scrap. In mass production, even a few millimeters of waste in width can accumulate to several tons or even tens of tons of material lost annually. Therefore, when selecting the width, it should be chosen to accommodate parts that are exactly multiples of the width, avoiding half-length gaps.

cold-rolled coil

3.From the perspective of cold-rolled coil production, is there a relationship between width and yield (utilization)?

Edge Crack Removal: During hot and cold rolling, microcracks may develop at the edges of the strip due to stress concentration. Steel mills must remove these cracked edges during finished product shearing (edge ​​trimming). For narrower specifications, the trimming amount accounts for a relatively high proportion of the total width; therefore, narrow cold-rolled coils typically have a slightly lower yield than wider ones.

Contract Batching: To improve efficiency, steel mills tend to group orders with similar widths together for production. If a customer orders a width that is too specific or too narrow, it can lead to scheduling difficulties and may even require separate rolling, thus affecting the overall hot-charging rate and yield of the batch.

cold-rolled coil

4.For downstream users (such as stamping plants), how to choose the width to maximize utilization?

**Layout Optimization:** When designing molds or shearing schemes, use computer-aided layout to find the optimal coil width that divides the part's width, minimizing any remaining width.

**Multi-Part Mixed Layout:** If one part cannot be perfectly filled with space, try placing another part of similar width on the same strip for mixed layout (common at blanking lines). This utilizes excess material and significantly improves the overall coil utilization rate.

**Avoiding the "Width Trap:** Sometimes, blindly pursuing greater width (assuming more material is better) can be counterproductive. For example, if a 1000mm wide coil can cut two parts perfectly, using a 1500mm wide coil might allow for three. However, if cutting three parts requires 1500mm, but after edge trimming, only 1490mm is actually usable, resulting in insufficient space for three parts or large amounts of excess material remaining after cutting three, ultimately reducing utilization.

 

5.When actually ordering, should you choose the standard width or any width? What impact will this have on utilization?

Standard Width (Commonly Used Width):

Advantages: Steel mills maintain regular inventory, ensuring stable production; prices are typically lower, and delivery times are shorter.

Disadvantages: Users may need to adjust their processes to accommodate the standard width, potentially leading to slightly lower utilization rates.

Any Width (Contract Width):

Advantages: Width can be customized to the user's optimal layout, theoretically maximizing utilization and minimizing edge waste.

Disadvantages: This is a non-standard product; steel mills may need to specially roll it, resulting in higher prices (additional markup), larger minimum order quantities, and longer delivery times.