MR, SPCC and SPTE tinplate sheets and coils are high-quality materials for a variety of packaging applications. MR (Medium Residue) has good corrosion resistance and formability and is widely used in food and beverage cans. SPCC (Cold Rolled Commercial Steel) is a versatile substrate with excellent mechanical properties and surface finish. SPTE (Single Layer Reduced Electrolytic Tinplate) has uniform thickness and high-quality surface, which is very suitable for precision packaging needs. GNEE These products are durable, excellent surface quality and suitable for safe contact with food, welcome to consult and place an order!
GNEE stocks SPCC MR Tin Sheet Coils with a fine glossy finish, contact us for more product information!
Specifications of MR SPTE Steel
| Item | Coil | Sheet | Tolerance |
| Annealing | BA/ CA | BA/ CA | - |
| Thickness | 0.14 - 0.55 mm | 0.14 - 0.55 mm | ± 3% |
| Width | 700 - 1,050 mm | 700 - 1,050 mm | -0/ +2mm |
| Length | - | 500 - 1,200 mm | -0/ +2mm |
| Weight | 3 - 15 MT per coil | 2 MT Max per bundle | ± 0.3% |
| Inside Diameter | 420/ 508 mm | - | ± 10mm |
| Outside Diameter | 1,800 mm | - | - |
| Remark | Temper | Hardness (HR30T) |
Yield Strength (Mpa) |
Features | Typical Application | ||
| JIS G3303-2008 |
ASTM A623M-06a |
DIN EN10202-2001 |
|||||
| Single Reduced (SR) |
T-1 | T49 | TS230 | 49 ± 3 | 230 ±50 | Deep drawing which requires large flexibility. | Drawn and ironed cans, nozzles, spouts, closures, mounting cup, oil filter. |
| T-2 | T53 | TS245 | 53 ± 3 | 245 ±50 | Moderate drawing with some stiffness. | Ring and plugs, dome tops, closures, shallow drawn parts. Drawing can, body, end for large can. | |
| T-2.5 | T54 | TS260 | 55 ± 3 | 260 ±50 | Combines the drawability of T-2 and the stiffness of T-3. | Battery shells, small can ends and bodies | |
| T-3 | T57 | TS275 | 57 ± 3 | 275 ±50 | Shallow drawing, proper stiffness to minimize fluting and prevent buckling. | Top and bottom of cans, can ends and bodies, large diameter closures, crown caps. | |
| T-3.5 | T59 | TS290 | 59 ± 3 | 290 ±50 | Items that require better formability than T-4. | General use, pail, 18L, 4L | |
| T-4 | T61 | TH415 | 61 ± 3 | 415 ±50 | Moederate forming. Moderate (comparatively large) stiffness. |
Can bodies and ends, crown caps, closures. Body and end for small can. |
|
| T-5 | T65 | TH435 | 65 ± 3 | 435 ±50 | High Stifness, excellent buckling resistance. Increased stiffness to resist buckling. | Can ends and bodies requiring intensity. Body and end for small can. |
|
| Double Reduced (DR) |
DR-7M | T71 | TH520 | 71 ± 5 | 520 ±50 | Moderate strength and stiffness with moderate forming. | DRD bodies, dome, Lug cap & 3 piece bodies |
| DR-8 | T72 | TH550 | 73 ± 5 | 550 ±50 | High strength and stiffness. | DRD bodies, end, Lug cap & 3 piece bodies | |
| DR-8M | T73 | TH580 | 73 ± 5 | 580 ±50 | |||
| DR-9 | T75 | TH620 | 76 ± 5 | 620 ±50 | Higher strength and stiffness. | DRD bodies, Lug cap & 3 piece bodies Thnner guage body, end, DRD cans, caps. |
|
| DR-9M | T76 | - | 77 ± 5 | 660 ±50 | |||
| DR-10 | - | - | 80 ± 5 | 690 ±50 | Very large stiffness and strength | DRD bodies, Lug cap & 3 piece bodies Thnner guage body, end, DRD cans, caps. |
|
| Note: Making cans with DR materials, please pay a special attention to the rolling direction. | |||||||
| 1. Type of Steel | |
| MR | It contains few residual minor constituents and has good corrosion resistance. |
| It is widely used for the applications of containers. | |
| L | It contains particularly few residual minor constituents as Cu, Ni, Cr, Mn. |
| It is suitable for the materials of containers requiring improved corrosion resistance. | |
| D | It is an aluminum killed steel. It is suitable for the applications. |
| that bear deep drawing or other workings which may produce Luder's lines patterns. | |
| Product Finish |
Code | Steel base | Product | Flow-melted | Nominal surface roughness of the steel base | |
| Euro | China | Ra (μm) | ||||
| Bright | BR | B | smooth | Tinplate | Yes | ≤ 0.35 |
| Fine stone | FS | R | fine stone | Tinplate | Yes | 0.25 - 0.45 |
| Stone | ST | R2 | stone | Tinplate | Yes | 0.35 - 0.60 |
| Silver | SG | S | shot blast | Tinplate | Yes | ≥ 0.90 |
| Matt | MM | M | shot blast | Tinplate | No | Various |
| Fine stone | FS | R2 | fine stone | TFS/ ECCS | - | 0.25 - 0.45 |
| Stone | ST | R1 | stone | TFS/ ECCS | - | 0.35 - 0.60 |
| Note 1 | Double reduced product is only supplied as stone finish | |||||
| Note 2 | Sub-classfied based on the surface finishing of the blackplate. | |||||
| Note 3 | The appearance is governed by: | |||||
| a) | the surface characteristics of the steel base which principally result from controlled preparation of the work rolls used during the final stages of temper rolling; | |||||
| b) | the mass of the coating applied; and | |||||
| c) | whether the tin layer is flow-melted or unflow-melted. | |||||
| Surface finish | Characteristic | |||||
| Bright finish | Glazed surface obtained after melting treatment of electrotinned smooth raw materail strip with extremely fine rubstone fingure by processing. | |||||
| Stone finish | Glazed surface obtained after melting treatment of electrotinned smooth raw materail stripfeaturing certain rubstone figures. | |||||
| Silver finish | Glazed surface obtained after melting treatment of electrotinned smooth raw material strip with rough matt furface. | |||||
| Matte finish | Matt surface of general matt raw material strip without melting treatment. | |||||
| 3. Coating Weight | ||||
| 1) Tinplate (ETP) | ||||
| Former Coating | Coating Weight | Nominal Coating Weight | Minimum average | |
| Designation | Code | (g/m2) | (g/m2) | |
Equally Coated |
10# | 1.1/ 1.1 | 1.1/ 1.1 | 0.9/ 0.9 |
| 20# | 2.2/ 2.2 | 2.2/ 2.2 | 1.8/ 1.8 | |
| 25# | 2.8/ 2.8 | 2.8/ 2.8 | 2.5/ 2.5 | |
| 50# | 5.6/ 5.6 | 5.6/ 5.6 | 5.2/ 5.2 | |
| 75# | 8.4/ 8.4 | 8.4/ 8.4 | 7.8/ 7.8 | |
| 100# | 11.2/ 11.2 | 11.2/ 11.2 | 10.1/ 10.1 | |
Differentially Coated |
25#/ 10# | 2.8/ 1.1 | 2.8/ 1.1 | 2.5/ 0.9 |
| 50#/ 10# | 5.6/ 1.1 | 5.6/ 1.1 | 5.2/ 0.9 | |
| 50#/ 25# | 5.6/ 2.8 | 5.6/ 2.8 | 5.2/ 2.5 | |
| 75#/ 25# | 8.4/ 2.8 | 8.4/ 2.8 | 7.8/ 2.5 | |
| 75#/ 50# | 8.4/ 5.6 | 8.4/ 5.6 | 7.8/ 5.2 | |
| 100#/ 25# | 11.2/ 2.8 | 11.2/ 2.8 | 10.1/ 2.5 | |
| 100#/ 50# | 11.2/ 5.6 | 11.2/ 5.6 | 10.1/ 5.2 | |
| 100#/ 75# | 11.2/ 8.4 | 11.2/ 8.4 | 10.1/ 7.8 | |
| 125#/ 50# | 15.1/ 5.6 | 15.1/ 5.6 | 13.9/ 5.2 | |
| Differential Marking | ||||
| a) Edge Marking : Low Coating Side with interrupted lines | ||||
| b) Line Marking : Heavy Coating Side with continuous lines | ||||
| c) Tin coating weight can be flexibly adjusted according to customer's requirement | ||||
MR electrolytic tinplate coil
SPTE Steel Packaging
FAQ
1. Is there any MOQ for tinplate coils and sheets?
A: We don't have MOQ for tinplate sheets, we can also provide samples.
2. What kind of terms of payment?
A: T/T, L/C are available.
3. What grams of the product can you offer?
A: These products can be customized according to your requirement.
4.Is free sample available?
A: Yes, free sample is available.
5. Can you do Customization & Reproduction if I provide a photo?
A: Yes, we do Customization & Reproduction service.
6. Does the packaging safe and arrive in good conditions?
A: Yes, safe Packing guarantee , all the products will arrive your door under good conditions.
We response to problem of shipping if there unfortunately is.
7. How long does it usually take to deliver the product?
A: We will make the shipment to you immediately. It will take about 18 to 40 days arrive worldwide. It depends on the specific quantity.
Hot Tags: mr spcc spte coil tinplate sheet and coil, China mr spcc spte coil tinplate sheet and coil manufacturers, suppliers, factory, cold rolled coil dc01, ASTM A53 GI Galvanized Steel Pipe, DX53D ZAM, galvalume coil size, colour gi sheet, Galvanized Gi Coil
