1.2 mm and 1.4 mm Cold Rolled Carbon Steel Sheet and Coil in DC01 and SPCC-SD

Aug 26, 2025 Leave a message

1.2 mm and 1.4 mm Cold Rolled Carbon Steel Sheet and Coil

Cold rolled carbon steel sheet and coil at 1.2 mm and 1.4 mm are the workhorse gauges of light construction and fabricated building products. They are thin enough to be folded, punched and roll formed on ordinary shop equipment, yet thick enough that a finished panel or frame keeps its shape under handling and wind load. The two grades most often specified at these gauges are DC01 and SPCC-SD, and they are supplied either as flat sheet cut to size or as coil for continuous lines.

What the DC01 and SPCC-SD Designations Mean

DC01 is the basic cold forming grade of the low carbon flat product family defined in EN 10130. Its low carbon content and annealed condition make it suitable for bending, beading, coining and simple drawing, which covers most building trim, frame and enclosure parts. Older drawings may still carry the DIN 1623 names St12 or FeP01; EN 10130 replaced that standard and DC01 replaced those designations, although the material class is the same.

SPCC belongs to JIS G 3141, which covers cold rolled carbon steel sheet and strip of commercial quality. The surface finish of the material is indicated by an additional code, and the SD suffix denotes the standard dull finish, a matte surface with a controlled roughness that holds paint and coating well. A dull finish is often preferred for building components because it hides handling marks and gives a uniform appearance after painting.

Grade Equivalents Across Standards

System Designation Note
European DC01 to EN 10130 Material number 1.0330; basic cold forming grade
Older German St12, FeP01 to DIN 1623 Superseded designations, now covered by DC01
Japanese SPCC to JIS G 3141 Commercial quality; finish code such as SD or SB
International CR1 to ISO 3574 Commercial quality cold reduced sheet
American ASTM A1008 Cold rolled carbon steel sheet, commercial quality
Chinese DC01 to GB/T 5213 Cold rolled low carbon sheet and strip for cold forming

The material number 1.0330 is the numeric designation that corresponds to DC01, and it is useful when a drawing quotes numbers instead of letters. In workshop language, cold reduced mild steel of this class is also called CR4, which is trade shorthand rather than a standard designation, so a drawing that uses it should be read together with the standard it is intended to follow. DC01 and SPCC are close but not identical: chemical limits, mechanical ranges and tolerances come from different documents, so substitution should be checked against the part requirements rather than assumed.

Why These Gauges Suit Building Components

Door skins, door frames and garage door panels formed on roll lines.

Roofing accessories, flashings, trims and cladding profiles.

Ceiling grid components, cable trays and ventilation duct sections.

Facings for insulated sandwich panels and backing sheets.

Shelving, lockers, kick plates, cabinets and shop fitting parts.

General light structural sections produced by cold roll forming or press braking.

At 1.2 mm and 1.4 mm the sheet holds a fold without cracking at normal bend radii, resists dents better than thinner material, and still cuts and punches cleanly. Widths, coil weights and sheet sizes are selected to match the forming line, with thickness and flatness tolerance agreed against a dimensional standard such as EN 10131.

Fabrication, Coating and Storage Practice

Cold rolled sheet forms best when the bend radius is kept at or above the limit recommended for the thickness, and when tooling is kept clean so that surface defects are not pressed into the strip. The matte dull finish improves adhesion for liquid paint and powder coating, but the surface should be degreased and, where required, given a conversion coating before painting. Because these gauges carry little excess material, storage discipline matters: sheets should be kept under cover, on dry dunnage and clear of the ground, and coil should be unwrapped only after it has reached room temperature so that condensation does not form between the wraps. Coils and bundles should be identified so that the certificate covering each heat can be traced to the parts produced from it.

Frequently Asked Questions

Q: What is DC01 material equivalent to?
DC01 corresponds to material number 1.0330 and is listed across European, ISO, Japanese and Chinese standards. The former DIN 1623 designations St12 and FeP01 now fall under DC01.

Q: Is DC01 the same as CR4?
CR4 is trade shorthand for cold reduced mild steel of this class. It is not a standard designation, so a drawing that uses it should be read with the standard it is intended to follow.

Q: What does SPCC-SD mean?
SPCC is commercial quality cold rolled carbon steel sheet to JIS G 3141, and the SD code denotes the standard dull surface finish, a matte surface suited to painting.

Q: What is DC04 material grade?
DC04 is a deep drawing steel of the DC grade family with excellent deep drawing properties under all types of deformation, used for high forming requirements.

Q: Can 1.2 mm cold rolled sheet be roll formed?
Yes. Both 1.2 mm and 1.4 mm grades are routinely roll formed into profiles for doors, cladding, ceiling and cable management systems.

Q: Which surface finish is better for painting?
A dull or matte finish holds coating more evenly than a bright finish, which is why the standard dull surface is common for building components that will be painted.