Cold Rolled Steel Coil and Sheet Grades: ST12, DC01, DC03, DC04, SPCC, SPCD, SPCE

Aug 26, 2025 Leave a message

Cold rolled steel coil, plate and sheet are ordered all over the world under a handful of short grade names, and the same sheet steel can be called ST12, DC01, DC03, DC04, SPCC, SPCD or SPCE depending on the standard that the buyer prefers. The family behind these labels is the same aluminium killed, low carbon, fully annealed cold reduced steel, differentiated mainly by how hard it is asked to work during forming.

One Family, Several Designations

The German grade series St12, St13 and St14 came from DIN 1623 and was replaced by the European series DC01 to DC06 in EN 10130, where DC stands for drawing quality. Japan specifies the same class of material in JIS G3141, with the grades SPCC for commercial quality, SPCD for drawing quality and SPCE for deep drawing quality. In North America the equivalent general purpose material appears in ASTM A1008 as commercial steel, CS Type B, with drawing steel and deep drawing steel following behind it.

When a customer orders ST12 coil but the mill issues an EN 10130 inspection certificate, both documents describe the same steel: DC01 with material number 1.0330. The older name survives because it is convenient, not because it defines a different product.

Equivalents Across Standards

ST12 is equivalent to DC01 in EN 10130, material number 1.0330, and to SPCC in JIS G3141

ST13 is equivalent to DC03 in EN 10130 and to SPCD in JIS G3141

St14 and St15 are covered by DC04 in EN 10130 and by SPCE in JIS G3141

DC05 and DC06 are interstitial free grades with titanium stabilisation, beyond the St grade series

Chemical Composition of the Drawing Grades

Formability in this family is controlled by keeping carbon, manganese, phosphorus and sulphur low and by fixing nitrogen with aluminium. The table gives the maximum values normally applied to each grade.

Grade C max % Mn max % P max % S max % Alt min % Ti max %
DC01, formerly St12 0.10 0.50 0.035 0.025 0.020 -
DC03, formerly St13 0.08 0.45 0.030 0.025 0.020 -
DC04, formerly St14 and St15 0.08 0.40 0.025 0.020 0.020 -
DC05, interstitial free 0.008 0.30 0.020 0.020 0.015 0.20
DC06, interstitial free 0.006 0.30 0.020 0.020 0.015 0.20

The step from DC01 down to DC06 is a step from a 0.10 % carbon maximum to a 0.006 % carbon maximum, and the addition of titanium in the interstitial free grades removes the last traces of carbon and nitrogen from solution. That is what allows the higher grades to be stretched into complex shapes without the Lüders lines and local necking that appear when a commercial quality sheet is pushed beyond its forming limit.

Which Grade for Which Job

Grade selection is normally driven by the severity of the forming operation rather than by strength, because all of these grades are soft and none of them is intended as a structural steel.

DC01 and SPCC: simple forming such as bending, embossing, beading, light drawing, roll forming and blanking

DC03 and SPCD: medium forming, including deep drawing and profiles that are difficult to form

DC04 and SPCE: high forming requirements, deep drawn panels and parts with tight radii

DC05 and DC06: the most severe drawing operations, where the material must flow far without tearing

A useful check before ordering is to compare the drawing ratio and the blank size with the forming limit of the grade. If the part has already failed once in a commercial quality sheet, moving one or two grades up the series is almost always cheaper than changing the tooling.

Coil, Plate and Sheet: Supply Forms and Tolerances

The grades above are supplied as cold rolled coil, as slit strip, as cut to length sheet and as flat blanks. Thickness normally runs from 0.3 mm to 3.0 mm and width from 600 mm to 1500 mm. Thickness tolerance, width tolerance, flatness and camber follow the standard named on the order, for example EN 10131 for cold rolled uncoated flat products, and surface finish is ordered in the European A, B, C classes or in the German FB and FC finishes. Coil inner diameter, coil weight and the position of the weld in a continuous coil are agreed case by case.

Frequently Asked Questions

Q: What is DC01 material equivalent to?
DC01 corresponds to ST12 in the withdrawn DIN 1623, to material number 1.0330, to SPCC in JIS G3141, to commercial steel CS Type B in ASTM A1008 and to DC01 in GB/T 5213.

Q: Is DC01 the same as CR4?
DC01 cold reduced mild steel is widely traded under the older British designation CR4. The two names are used interchangeably for the same soft, cold reduced sheet, although DC01 is the current designation and should be quoted on new orders.

Q: What is DC03 and what is it used for?
DC03 is a low carbon drawing quality steel with a maximum carbon content of about 0.08 % and good cold formability. It is used where forming requirements such as deep drawing and difficult profiling go beyond what DC01 can take.

Q: What is DC04 steel?
DC04 is a deep drawing grade of the DC family with excellent drawing properties under all types of deformation. It suits high forming requirements and is the usual choice for deep drawn panels and housings.

Q: Is DC01 steel magnetic?
Yes. These are ferritic low carbon steels, so they are magnetic and are used in electrical enclosures and components where formability, strength and magnetic response are all needed.

Q: What is the difference between SPCC, SPCD and SPCE?
They are the JIS G3141 commercial, drawing and deep drawing quality grades in order of increasing formability. SPCC is the general purpose sheet, SPCD takes medium forming and SPCE is intended for deep drawn parts.