18 Gauge Cold Rolled Steel Coil: DC01 and CR4 Grades, Tolerances and Forming

Aug 28, 2025 Leave a message

What "18 Gauge" Means for a Cold Rolled Coil

Gauge is a thickness convention rather than a fixed dimension. On the standard gauge for sheet and strip steel, 18 gauge equals 0.0478 in, which converts to 1.214 mm, and mills and service centres normally trade the size as a 1.2 mm cold rolled coil. Gauge numbers run in reverse, so 18 gauge is thinner than 16 gauge and heavier than 20 gauge. A purchase order that states only "18 gauge" should therefore be checked against the intended 1.2 mm nominal metric thickness and the matching tolerance band before rolling.

DC01, CR4, DC03 and DC04 Explained

DC01 is the entry cold forming grade of the DC family. It is a low carbon, fully killed, cold rolled flat product supplied to EN 10130 and is the volume workhorse for bending, roll forming, lock seaming and light drawing. In the United Kingdom and Ireland the same material is widely ordered as CR4, and CRCA, or cold rolled close annealed, is the traditional mill term for the annealed and skin passed condition. DC03 and DC04 move up the drawability ladder. DC03 is an aluminium killed grade with improved elongation and normal anisotropy, and DC04 is a deep drawing grade with a higher plastic strain ratio and a higher work hardening exponent, which allows deeper cups with fewer intermediate anneals. Selection is driven by the drawing ratio and the number of forming stages.

Grade Standard Yield strength Re (MPa) Tensile strength Rm (MPa) Elongation A80 (min.) Typical use
DC01 / CR4 EN 10130 140-280 270-410 28% Bending, roll forming, light drawing
DC03 EN 10130 140-240 270-370 34% Moderate drawing, enclosures
DC04 EN 10130 140-210 270-350 38% Deep drawing, visible panels

The figures above are the typical requirement levels of EN 10130, stated as ranges because the acceptance values are those printed on the mill test certificate. Chemistry is what separates the grades: indicative maximum contents fall from 0.12% carbon, 0.60% manganese, 0.045% phosphorus and 0.045% sulphur for DC01 to 0.08% carbon, 0.40% manganese, 0.030% phosphorus and 0.030% sulphur for DC04. Lower interstitial content raises ductility and suppresses the yield point elongation that otherwise shows up as Luders lines on visible panels.

Surface Finish, Flatness and Coil Dimensions

Finish: matte, also called dull, is the normal mill finish for forming grades; a bright finish is available for parts that will be painted or lacquered.

Surface quality: level A for exposed applications and level B for non exposed parts, either of which may be ordered oiled.

Tolerances: thickness, width, length, flatness and edge camber are controlled to EN 10131 unless a tighter mill agreement is agreed at enquiry stage.

Edges: mill edge or trimmed edge, with trimmed edge preferred when the strip feeds a press or an automated roll former.

Coil build: inner diameter normally 508 mm or 610 mm, outer diameter up to about 1500 mm, coil weight typically 3 to 10 tonnes, with slit coil from 20 mm width.

Forming, Welding and Finishing Notes

The 1.2 mm section bends easily, and a minimum inside bend radius of roughly one times the thickness is a safe starting point for DC01 across the rolling direction, while DC03 and DC04 tolerate smaller radii. Spot, seam, laser and arc welding all suit the grade because the carbon equivalent is low, and no preheat is needed. Coil supplied oiled should be degreased before painting or powder coating, and parts that will be exposed outdoors should be phosphated or coated, because plain cold rolled steel carries no corrosion protection of its own and will rust in damp storage. Stacked coil should be kept indoors on timber bearers.

Where 18 Gauge Cold Rolled Coil Is Used

Typical end uses include office and domestic appliance cabinets, automotive brackets and inner panels, shelving and racking, drums and general containers, and the base material for subsequent hot dip galvanising, electro galvanising or organic coating lines. The grade is equally common in jigs, fixtures and general sheet metal work, where a smooth, dimensionally stable surface is valued.

Frequently Asked Questions

Q: Is DC01 the same as CR4?
Yes. CR4 is the traditional British designation for the same cold reduced, low carbon, fully killed material now ordered as DC01 to EN 10130, so the two names can be used interchangeably on a mill order.

Q: What thickness is 18 gauge cold rolled coil in millimetres?
On the standard gauge for sheet steel, 18 gauge is 0.0478 in, or 1.214 mm, which is quoted commercially as a 1.2 mm nominal thickness.

Q: Is DC01 a mild steel?
Yes. DC01 is a low carbon mild steel produced by cold rolling and annealing, which gives it a smooth surface, uniform thickness and good ductility rather than high strength.

Q: When should DC04 be chosen instead of DC01?
Choose DC04 when the part needs deep drawing with a high draw ratio or tight cup radii in a single press stroke. DC01 suits bending, roll forming and shallow draws.

Q: Does cold rolled coil need to be oiled?
Light oiling is recommended for storage and press work because it limits surface rust and improves lubricity. Oiled coil must be degreased before welding that will be painted, or before coating.

Q: Can 18 gauge cold rolled coil be galvanised later?
Yes. DC01 is a common substrate for hot dip galvanising, electro galvanising and organic coating lines, provided the surface is clean and free from heavy rust or oil.