Hot Rolled Black Structural Carbon Steel Coil: Q195, Q235, Q355, Q345 and DC01 Explained

Sep 09, 2025 Leave a message

What Hot Rolled Black Coil Means in Practice

Hot rolled black coil is the mill's as-rolled flat product. The strip leaves the finishing stands at high temperature, is coiled, and is supplied without pickling, oiling or metallic coating. The surface carries the characteristic blue-grey oxide scale, and dimensions follow the hot rolled standard: GB/T 709 in China, EN 10051 in Europe, ASTM A568/A568M in North America. It is the lowest-cost flat product form and the correct starting point for structural, tube-making and general engineering work where appearance is secondary and thickness is 1.2 mm or more.

Black therefore describes a supply condition, not a grade. The grades that appear in the same title or quotation describe different things: Q195, Q235B and Q355B are structural steels defined by minimum yield strength, DC01 is a cold rolled forming grade, and Q345 is a legacy designation that has been replaced.

Q195, Q235 and Q355: The Chinese Structural Series

GB/T 700 defines the carbon structural steel series in which the number indicates the minimum yield strength in megapascals: Q195, Q215, Q235 and Q275. GB/T 1591 defines the low-alloy high-strength series: Q355, Q390, Q420, Q460 and higher. Both series are supplied hot rolled, and both are commonly quoted as black coil or plate.

Grade Standard Minimum yield strength Tensile strength Typical use
Q195 GB/T 700 195 MPa, thickness up to 16 mm 315 to 430 MPa Light sections, wire, welded tube
Q235B GB/T 700 235 MPa, thickness up to 16 mm 370 to 500 MPa General structures, purlins, plates
Q355B GB/T 1591 355 MPa, thickness up to 16 mm 470 to 630 MPa Bridges, towers, heavy structures
Q345 GB/T 1591, legacy edition 345 MPa, thickness up to 16 mm 470 to 630 MPa Superseded by Q355

One correction matters for technical buyers. Q345 belongs to the earlier edition of GB/T 1591 and is no longer a current grade; the later editions replaced it with Q355, keeping the same strength class in practice while aligning the designation with the 16 mm reference thickness. Drawings and purchase orders that still call for Q345 should be re-mapped to Q355B unless an existing contract fixes the older designation. A second point of confusion is the letter suffix: Q235A and Q235B differ in impact-testing temperature and sulphur and phosphorus limits, not in strength, and the suffix must always be stated on the order.

DC01: A Cold Rolled Forming Grade, Not a Structural Steel

DC01 comes from a different family altogether. EN 10130 defines the DC series of cold rolled low-carbon steels for cold forming, running from DC01 for basic forming through DC03, DC04, DC05, DC06 and DC07 as drawing severity increases. DC01 is the basic grade and was historically known as St12 or FeP01.

Typical DC01 limits under EN 10130 are a maximum carbon content of about 0.12%, maximum manganese of about 0.60%, and minimum elongation after fracture of roughly 28%. That combination suits bending, coining, beading and light drawing. Because DC01 is cold rolled, it arrives with a smooth, clean surface and a tight thickness tolerance rather than mill scale, and it is selected for formability and surface quality rather than for load-carrying capacity. A Q235B structural coil and a DC01 coil are therefore not interchangeable, even when the thickness and width happen to match.

Where S45 and ASTM A106 Fit, and What to Watch

Two designations commonly appear beside these coil products and deserve clarification.

S45 or S45C. A medium-carbon steel specified in JIS G4051 and, in the Chinese system, as 45 steel under GB/T 699, with a carbon content of roughly 0.42% to 0.48%. It is a bar and forging material for shafts, gears and spindles. It is not normally supplied as wide coil, and its higher carbon content makes it unsuitable for cold bending.

ASTM A106. This specification covers seamless carbon steel pipe for high-temperature service, not flat-rolled coil. Where a coil product must satisfy an American structural specification, the correct references are ASTM A36/A36M for general structural steel or ASTM A572/A572M for high-strength low-alloy grades.

Mixing a pipe specification into a coil enquiry is one of the most common causes of rejected deliveries, because the mechanical property sampling, tolerances and inspection requirements are written for a different product form.

Dimensions, Tolerances and Supply Condition

Item Typical offer
Thickness 1.2 mm to 16 mm as-rolled; thinner gauges require cold rolling
Width 600 mm to 2000 mm, depending on mill
Coil inner diameter 508 mm, 610 mm or 762 mm
Coil weight 3 t to 30 t
Edge condition Mill edge or slit edge
Surface As-rolled oxide scale, optionally oiled
Dimensional standard GB/T 709, EN 10051 or ASTM A568/A568M

Thickness tolerance class changes the delivered price materially, so tolerance should be agreed in the same clause as the grade. For welded tube and cold forming lines, a tighter tolerance and an oiled, scale-controlled surface usually reduce downstream scrap enough to justify the premium.

Checks Before Placing an Order

Confirm the grade and its letter suffix, and the edition of the standard that applies.

Ask for a mill test certificate issued to EN 10204 3.1, with heat analysis and mechanical properties.

Agree the thickness tolerance class, width tolerance and edge condition in writing.

State whether pickling and oiling are required, since as-rolled scale is unsuitable for some forming operations.

Record coil inner diameter, coil weight and packing method so that handling equipment on site fits.

Check that the quantity matches a full coil or a defined slit width, because part coils carry higher unit cost.

Applications

Hot rolled black coil and its cold rolled relatives feed structural fabrication, purlins and frames, welded pipe and tube mills, general machinery, agricultural equipment, storage racking and a very large share of the world's light engineering output. Where the surface is exposed, the mill finish is normally painted or powder coated; where it is concealed inside a structure, the black condition is used as supplied.

Frequently Asked Questions

Q: Is hot rolled black coil the same as pickled and oiled coil?
No. Black coil retains the mill oxide scale. Pickled and oiled coil has had the scale removed by acid pickling and is then oiled to prevent flash rusting, which gives a clean, formable surface at higher cost.

Q: Can Q235B and DC01 be substituted for one another?
Not as a general rule. Q235B is a hot rolled structural steel selected for strength; DC01 is a cold rolled forming steel selected for surface quality and ductility. Substitution requires engineering review against the actual application.

Q: Why is Q345 no longer listed in current standards?
It was a grade of the earlier GB/T 1591 edition. Later editions replaced it with Q355, which covers the same strength class, so new projects should specify Q355B instead of Q345.

Q: Does the kind of steel coil always need a mill test certificate?
For structural and pressure-related work, yes. A certificate to EN 10204 3.1 provides heat analysis and mechanical test results traceable to the coil, which is normally required by specifiers and inspectors.

Q: What is the difference between the thickness tolerances of hot and cold rolled coil?
Cold rolled coil is produced to appreciably tighter thickness and flatness tolerances than hot rolled coil, which is one reason it is chosen for stamping and precision parts despite the higher price.

Q: How should hot rolled black coil be stored on site?
Keep coils under cover on timber dunnage with free air circulation, avoid standing water and keep the material dry. Surface rust on black coil is normal and superficial, but wet storage can cause deep pitting that affects the finished part.