SGCC Galvanized Steel Applications in the Energy Sector

Sep 01, 2025 Leave a message

Why SGCC Galvanized Steel Suits Energy Infrastructure

SGCC is a commercial quality continuous hot dip zinc coated steel sheet grade defined in JIS G3302. Its combination of formability, weldability and a metallurgically bonded zinc coating has made it a default material for the structural and enclosure components of energy projects, which must survive decades of outdoor exposure with minimal maintenance. Zinc protects the base metal twice over: it seals the surface as a barrier, and it acts as a sacrificial anode so that scratches, sheared edges and bolt holes remain protected.

Coating selection drives service life. Thin enclosure panels are usually supplied with lighter coatings, while exposed support structures, container bodies and platform members take heavier coatings. The table below summarises the requirements met in each energy application covered in this article.

Application Typical component Zinc coating requirement
Photovoltaic power station Mounting rails, C and U sections, cable trays 80 g/m2 and above
Energy storage station Container side panels and roof, battery racks 100 g/m2 and above
Wind power plant Ladder steps, platform guardrails, cable racks Heavier coating with a friction friendly surface
Oil and gas site Platform treads, guardrail posts, pipe supports, signage Heavy coating for saline and soil exposure
Thermal power plant Ventilation ducts, maintenance platforms, cable trays Heavy coating plus a high temperature resistant lining

Photovoltaic Power Stations

Mounting systems are the core application. They hold modules to roofs, ground and trackers, carrying panel weight together with long term wind and snow loads. SGCC sheet is stamped and bent into C and U shaped members or custom profiles and then bolted into arrays. The coating resists dew and driving rain so that rust cannot loosen clamps or tilt panels, while the formability of the grade allows the bracket shapes needed for sloped roofs and undulating terrain. Field experience puts service life in the 15 to 20 year range, matching the operating period of a typical plant.

Inverter and combiner box enclosures form a second application. Cold rolled and stamped sheet of roughly 1.5 mm to 2.5 mm forms the casing, often finished with a UV resistant polyester coating. The enclosure sheds rain, and the ventilation openings assist heat dissipation so that power electronics remain stable across an outdoor range of about minus 30 to plus 60 degrees Celsius.

Cable protection tubes and trough type cable bridges complete the package. Cables running from the array to the inverter are exposed to rain, soil moisture, rodents and impact, and a galvanized enclosure keeps the sheath intact and power transmission safe.

Wind Power Plants

Modern towers stand 80 to 120 metres tall, so ladder steps, rest platforms and guardrails must stay sound for the working life of the machine. Galvanized members resist the humid air and abrasive dust that collect at the tower base, and the zinc surface offers a moderate friction coefficient that helps prevent slips during ascent.

Inside the nacelle, cable racks, equipment mounting frames, distribution boxes and tool cabinets are also fabricated from SGCC sheet. Although the nacelle is enclosed, vaporised gear oil leaves a fine film; galvanized surfaces tolerate this far better than bare cold rolled steel and are easier to clean, reducing the risk of long term oil related corrosion.

Energy Storage Stations

Container bodies and internal frames are a demanding duty. Side panels and roofs formed from SGCC sheet with a zinc coating of 100 g/m2 and above, combined with a fire resistant insulating layer, resist driving rain and high surface temperatures while the sacrificial action of the zinc controls corrosion during prolonged wet periods such as a long rainy season.

Battery racks and inverter mounting brackets inside the container carry packs that can weigh several tonnes, so rigidity matters as much as corrosion resistance. The same material also tolerates the trace electrolyte leakage that occurs during normal battery operation. Perimeter fencing, welded mesh and frame guardrails around a storage site use the same grade, because they need long weathering life without frequent repainting while still resisting impact.

Oil, Gas and Thermal Power

Wellhead operating platforms give access to valves and instruments, and guardrails protect the operators working there. Non-slip treads and guardrail posts in SGCC resist oil and gas moisture and the saline and alkaline soils typical of coastal fields, and the fabricated cost stays well below that of stainless steel.

Long distance pipelines need ground supports at regular intervals to prevent settlement, and these brackets resist soil moisture and microbiological corrosion such as sulphate reducing bacteria. Pipeline warning signage uses the same coated sheet so that lettering stays legible outdoors and the base plate does not rust or peel.

In thermal power generation, ventilation ducts serving boiler and turbine halls carry hot humid air. The duct casing is formed from SGCC with a high temperature resistant internal coating, and the zinc layer controls the rust that condensation would otherwise cause on duct walls. Maintenance platforms and stair railings use the same material to resist fly ash adhesion and cut cleaning costs. Equipment supports and cable trays serving flue gas desulphurisation towers operate in a weakly acidic mist; the zinc layer reacts to form a dense protective oxide film that slows attack and can extend service life by several years compared with unprotected carbon steel.

Frequently Asked Questions

Q: What does the SGCC designation mean?
SGCC is a commercial quality continuous hot dip zinc coated steel sheet grade defined in JIS G3302, intended for formed and welded components that require corrosion protection.

Q: How much zinc coating is needed for photovoltaic mounting?
Mounting rails, clamps and cable trays are commonly specified with a zinc coating of 80 g/m2 and above so that the system outlasts the module warranty period.

Q: How long does SGCC last in a solar plant?
With the usual coating mass and sheltered detailing, service life of about 15 to 20 years is a reasonable expectation, matching the operating life of the plant.

Q: Can SGCC be welded on site?
Yes, but the zinc layer must be removed locally before welding and the joint recoated afterwards, with fume extraction provided because zinc vapour is generated.

Q: Why is a heavier coating used on storage containers?
Container bodies face standing moisture, condensation and high surface temperatures, so 100 g/m2 and above is used to keep the sacrificial zinc reserve adequate.

Q: Is SGCC suitable for coastal oil fields?
It is widely used there provided the coating mass is increased and cut edges, welds and drilled holes receive a compatible repair coating against salt laden air.