Are Galvanized Coils Used for the Outer Shell of Shared Lockers?

Nov 03, 2025 Leave a message

Why Galvanized Coil Suits Shared Locker Shells

Shared lockers are placed in subway stations, campuses, shopping malls, factories and outdoor plazas, so the shell has to survive humid air, rain, cleaning chemicals and daily impact for years. Hot-dip galvanized steel coil meets that requirement at a fraction of the cost of stainless steel, which is why it remains the default material for locker cabinets, parcel lockers and storage cabinets.

Three properties drive the choice. First, the zinc coating protects the steel by a combination of barrier action and sacrificial action: even where the surface is scratched, the zinc surrounding the damaged area corrodes preferentially and keeps the underlying steel sound. Second, cold-rolled steel substrate gives the cabinet the stiffness needed to carry doors, shelves and electronic components. Third, the material is made for modern sheet metal processes, so it can be laser cut, punched, bent and roll formed into the complex internal geometry a locker bank requires.

Grades and Typical Specifications

Item Option
Substrate grades SGCC or DX51D+Z for general forming; SGCD or DC03 for drawn parts
Zinc coating mass Z100 to Z275 g/m2 total both sides, depending on exposure
Thickness 0.5 mm to 1.2 mm typical for door and side panels
Surface finish Zero spangle or regular spangle, painted or unpainted
Surface treatment Chromate passivation or anti-fingerprint oil for painted shells
Coil form Wide coil for in-house slitting, or slit strip and cut lengths

For indoor installations a coating of Z100 to Z140 is normally sufficient, while lockers placed outdoors or in wet areas are usually specified at Z275. The thickness should be chosen from the stiffness requirement of the largest unsupported panel: a thin gauge that deflects under load will need stiffening ribs, which may cost more than a heavier gauge.

The Cut-Edge Problem and How to Solve It

The one genuine weakness of a galvanized shell is the cut edge. Laser cutting, punching and shearing remove the zinc at the cut line and expose bare steel, and those edges are the first points where red rust appears. The standard solution is a coated finish applied after forming: the parts are degreased, given a conversion or phosphate pre-treatment, and then finished with electrostatic powder coating that wraps around the edges and seals them.

Powder coating also supplies the colour and the brand appearance that locker operators need. To make the coating reliable, the passivation layer left by the mill must be removed in pre-treatment, the line should be free of zinc dust and swarf, and the cure schedule should follow the powder supplier's data sheet. Where a shell will not be painted, edge repair paint or a zinc-rich touch-up should be applied to cut edges and drilled holes.

Galvanized Steel Compared with Stainless Steel

Factor Galvanized steel shell Stainless steel shell
Corrosion resistance Good with an intact coating; depends on cut-edge sealing Excellent, including at cut edges
Cost of material Low to moderate High
Strength and stiffness High, resists impact and stacking High, higher ductility and toughness
Weight Heavier than aluminium, comparable to mild steel Slightly lighter for equal stiffness
Fabrication Easy to laser cut, punch and bend Harder on tooling, more springback control needed
Finishing Powder coating or painting required or preferred Often used bare, brushed or polished
Best fit High-volume locker banks and cost-controlled projects Premium installations and aggressive environments

The trade-off is therefore cost against maintenance. Galvanized steel with a properly applied powder coating gives a durable shell at a moderate price for large deployments; stainless steel suits premium sites or locations with salt or chemical exposure, but raises material and processing cost considerably.

Production Flow and Specification Notes

Typical production sequence: galvanized coil → slitting or levelling → laser cutting or stamping → bending and forming → welding or riveting of the frame → degreasing and phosphate pre-treatment → electrostatic powder coating and curing → assembly with locks, hinges and control boards.

Drawing review: confirm the panel thickness, the inner bending radius and the stiffening details before releasing the coil, because galvanized sheet needs a slightly larger bend radius than cold-rolled sheet of the same thickness.

Coil acceptance: check coating mass, thickness, width, flatness and surface condition on delivery, and verify that the delivered grade matches the certificate.

Handling: keep coils indoors and dry, wear clean gloves, and avoid dragging sheets over each other, which damages the coating before the parts are even painted.

Frequently Asked Questions

Q: Is galvanized coil strong enough for a locker shell?
Yes. Cold-rolled galvanized steel has ample strength and stiffness for cabinet doors, side panels and frames. Thin panels may need ribs or returns to control deflection under load.

Q: Why does rust appear on the cut edges?
The zinc coating is removed at the cut, exposing steel. Sealing the edges with a powder coating after pre-treatment, or with a zinc-rich repair paint, prevents rust from starting there.

Q: Can the shell be left unpainted?
It can, and the zinc coating will protect it, but appearance varies and fingerprints show easily. Chromate passivation or an anti-fingerprint treatment is used for unpainted indoor cabinets.

Q: How thick should the sheet be for a locker door?
Most indoor locker doors are made from 0.6 mm to 1.0 mm galvanized sheet, with heavier gauges for outdoor units and large unsupported panels.

Q: Does galvanized steel cost less than stainless steel?
Yes, substantially less in material cost and generally easier on cutting and forming tooling, which matters in high-volume locker production.

Q: Are galvanized coils suitable for laser cutting?
Yes. The zinc coating vaporises in the cut zone, so the process requires suitable extraction and, for thick sections, attention to cut quality. Cut edges then need protective sealing.