Besides the composition of the zinc bath, what other factors affect coating continuity?

Sep 08, 2025 Leave a message

Besides the composition of the zinc bath, what other factors affect coating continuity?

In addition to the composition of the zinc bath, the coating continuity of hot-dip galvanizing (including S235JR products) is also affected by multiple factors, including substrate pretreatment, process parameters, workpiece structure, and production operations. These factors are as follows:
1. Substrate Surface Pretreatment Quality

The cleanliness of the substrate (S235JR steel) surface directly determines whether the zinc bath can evenly wet the surface. The presence of impurities or oxide layers will hinder the reaction between zinc and iron, resulting in a discontinuous coating.

Oxide scale and rust are not completely removed.

Oxide scale (Fe₃O₄, Fe₂O₃) or rust on the steel surface creates a physical barrier, preventing direct contact between the zinc bath and the iron substrate. This can result in partial coating failure (skip plating) or a loose, poorly adhered zinc layer.

Oil and grease residue
Residual oils (such as rust preventative oil and cutting fluid) left during rolling and storage can burn or carbonize in the zinc bath, forming a carbon film or bubbles that coat the substrate surface, preventing the zinc from penetrating and resulting in areas of missing coating or pinholes.
Improper pickling
During pickling (de-scaling), if the acid concentration is insufficient or the pickling time is too short, the scale is not completely removed; or if the pickling is excessive, the substrate surface is corroded ("over-pickling"), resulting in a loose iron matrix that is susceptible to penetration by the zinc bath, forming a porous, discontinuous coating.
If water rinsing is not thorough after pickling, residual acid (such as hydrochloric acid) can enter the zinc bath, reacting with the zinc to produce hydrogen, which can form bubbles in the coating and disrupt its continuity. 2. Workpiece Condition Before Entering the Zinc Pot
Workpiece Temperature
If the workpiece temperature is too low before entering the zinc pot (e.g., if preheating is not done or is insufficient), contact with the hot zinc bath will cause the zinc bath to cool down instantly in certain areas, causing a sudden increase in viscosity and a decrease in fluidity. This makes it difficult for the zinc bath to fill the workpiece surface (especially around grooves and welds), resulting in "cold shuts" or missing plating.
If the workpiece surface is moist (e.g., if it has not been dried after pickling), this moisture will instantly vaporize upon entering the zinc bath, generating a large amount of steam that impacts the zinc bath, causing the zinc layer to be partially "dispersed," resulting in pores or missing plating.
Workpiece Surface Condition
Sharp edges, burrs, or weld spatter on the workpiece surface can disrupt the fluidity of the zinc bath, leading to a thin zinc layer at the edges or missing plating due to the "tip effect." Spatter can also obscure the substrate, resulting in areas without coating.
3. Controlling Galvanizing Process Parameters
Immersion Time
If the immersion time is too short, the zinc bath will not react fully with the substrate, resulting in incomplete zinc coating. This can easily lead to missing plating or a thin zinc layer (pinholes). Too Long Zinc Dipping Time: Excessive dissolution of the base iron into the zinc bath results in a large amount of zinc-iron alloy slag, which adheres to the workpiece surface and forms "slag nodules," leading to discontinuous coatings. Furthermore, an excessively thick alloy layer may embrittle and crack, compromising its integrity.

Workpiece Insertion Angle and Speed

If the workpiece is vertical or tilted at an inappropriate angle (e.g., a groove on a complex structural part facing downward), the zinc bath will not be able to properly fill any corners, preventing air from escaping and forming "air pockets" (areas devoid of zinc).

Slow Insertion Speed: The workpiece surface is susceptible to oxidation (due to prolonged contact with air at high temperatures), forming an oxide film that hinders zinc bath infiltration. Excessive speed may entrap air and create bubbles.

Zinc Bath Agitation and Zinc Bath Flowability
If excessive zinc slag accumulates at the bottom of the zinc bath (and is not promptly cleaned), the workpiece will become contaminated upon contact, forming slag spots. Furthermore, insufficient convection in the zinc bath can lead to localized uneven composition and temperature, affecting coating uniformity. IV. Workpiece Structure Design
Workpieces with complex structures are prone to geometrical obstacles, preventing adequate zinc coating. Common problems include:
Closed or semi-closed structures: For example, closed steel pipes or closed-end box-like workpieces prevent air from evacuating during zinc immersion, creating "air pockets" and resulting in areas without coating.
Narrow gaps or deep holes: For example, narrow weld gaps or deep bolt holes prevent zinc from penetrating due to surface tension, resulting in missed coatings.
Large flat surfaces: If the workpiece shakes during zinc immersion, the zinc can easily form "ripples" or "sagging" on the surface, causing the zinc coating to become thin or accumulate (which can easily fall off, exposing the base material).
V. Post-treatment and Operational Standards
Cooling after zinc removal
Excessively rapid cooling (such as direct water cooling) can cause cracks in the coating due to thermal stress. Excessively slow cooling can lead to surface oxidation (forming ZnO). This detachment of the oxide layer exposes the underlying zinc layer, and discontinuous underlying layers can result in a loss of protection. Hanger Design and Workpiece Suspension
If the hanger contacts the workpiece too closely, it will obstruct the contact area, resulting in "hanger marks" (partially missing coating). Poor conductivity (e.g., when used for electrogalvanizing) will result in a thinner zinc layer near the contact point.

Operational Errors
Incomplete immersion of the workpiece in the zinc bath, scratches on the zinc layer caused by collisions during galvanizing, and missed areas of unchecked plating can all directly damage the continuity of the coating.

Summary
Coating continuity is the result of multiple factors, including substrate pretreatment, process parameters, workpiece structure, and operating procedures.

Core Logic: Any factor that hinders sufficient contact between the zinc bath and the substrate iron or disrupts uniform zinc crystallization (such as impurities, structural blind spots, or process failure) will result in a discontinuous coating.

Key Control Points: In addition to the zinc bath composition, strict control of substrate rust and oil removal quality, galvanizing time and temperature, workpiece structure rationality, and operating procedures is required to ensure a continuous and complete protective coating on S235JR galvanized products.