Galvanized steel sheet is a family of products rather than one material. Two sheets with the same dimensions can differ in coating process, coating mass, surface finish and forming quality, and those differences decide whether the sheet performs well in a roofing profile or fails in a deep-drawn appliance panel. The categories below follow the classification used by coating lines, then relate them to the grade designations DX51D, DX52D and DX53D and to a typical Z120 g/m² coating on 0.3 mm sheet.
Categories by Production and Processing Method
Hot-dip galvanized sheet. Cold-rolled strip is passed continuously through a molten zinc bath, so a zinc layer adheres metallurgically to both surfaces. Continuous lines dominate production because they give uniform coating mass and a controlled surface.
Galvannealed (alloy) sheet. The strip is also hot dipped, but immediately after leaving the bath it is reheated to around 500 °C so that zinc and iron interdiffuse into a zinc-iron alloy layer. The result is a matte, grey surface with excellent paint adhesion and good weldability, widely used for automotive and appliance bodies.
Electro-galvanized sheet. The coating is deposited electrolytically instead of by dipping. The coating is thinner and more uniform, processability is good, but corrosion resistance in the same environment is lower than that of a hot-dip coating of comparable mass.
Single-sided and double-sided galvanized sheet. Single-sided product is coated on one face only, which improves welding, painting and forming behaviour on the uncoated side. To overcome the unprotected face, a variant carries a very thin zinc layer on the second side as well.
Alloy and composite coatings. Zinc is combined with other metals such as aluminium, or applied as a multi-layer coating, to combine barrier protection with paintability. These products sit alongside the standard zinc coatings rather than replacing them.
Understanding the DX and SGCC Grade Designations
The grade in the title belongs to the European coating standard EN 10346, which consolidated the older EN 10327 and DIN 17162 designations. The DX series is defined by coating, formability class and coating mass, written as a suffix such as +Z for pure zinc.
| Grade | Formability quality | Typical use |
|---|---|---|
| DX51D | Commercial quality, general purpose | Roofing and cladding sheets, ducting, simple bent parts |
| DX52D | Drawing quality | Panels and housings requiring moderate forming |
| DX53D | Deep drawing quality | Deep-drawn appliance and automotive components |
DC51D+Z covers the same commercial-quality level with controlled chemistry limits, and the Japanese designations SGCC, SGCD1, SGCD2 and SGCD3 of JIS G3302 run in the same order of increasing drawability. Equivalents also exist under ASTM A653M, where the coating class is quoted separately from the steel grade. A buyer comparing quotations from different mills should therefore compare three things at once: the steel designation, the coating mass and the surface finish.
Coating Mass, Spangle and Surface Finish
Coating mass is written as Z followed by the total mass of zinc on both surfaces in grams per square metre. Z120 means 120 g/m² total, that is approximately 60 g/m² per side. For DX51D on 0.3 mm sheet, Z120 is a common specification for general building and industrial work, while heavier classes such as Z275 are selected for aggressive outdoor exposure. Coating mass is the primary lever on service life, so it should be stated explicitly on every order.
Spangle describes the visible crystalline pattern of the zinc. Regular spangle shows the full crystalline flower; minimised (small) spangle is produced through cooling and bath control or grain refiners, and zero spangle is achieved by skin-passing or by inhibiting crystal growth, giving an almost uniform, smooth surface. Large spangle is chosen where a traditional appearance is wanted and paint uniformity is not critical, while zero spangle is preferred for painted appliance and automotive panels.
Typical Specification Range
| Item | Range |
|---|---|
| Standards | JIS G3302 / ASTM A653M / EN 10346 (replacing EN 10327 and DIN 17162) |
| Grades | SGCC, DC51D, DX51D, DX52D, SGSS, SGCD1, SGCD2, SGCD3 |
| Thickness | 0.12–3.5 mm |
| Width | 600–1250 mm (common: 914, 1000, 1200, 1219, 1220, 1250 mm) |
| Zinc coating | 30–275 g/m² total |
| Spangle | Regular, minimised, zero, large |
| Hardness classes | Soft (approx. HRB 60), medium (HRB 60–85), full hard (HRB 85–95) |
| Coil inner diameter | 508 mm or 610 mm |
| Coil weight | Approximately 4–6 t |
| Packing | Seaworthy export packing: waterproof paper, steel strapping, wooden pallet or case |
These figures are production ranges, not guarantees for a single order. Thickness, width, coating mass and mechanical class must be agreed together, because pushing a coating to the top of the range while demanding the thinnest sheet and the tightest formability adds cost and lengthens the delivery schedule.
Selecting the Right Category
Roofing, cladding and ducting in mild environments - hot-dip DX51D with regular spangle and a moderate coating mass gives the best cost-performance balance.
Panels that will be painted - galvannealed or zero-spangle hot-dip sheet removes the risk of spangle showing through thin paint films.
Parts with difficult draws - move up to DX53D or SGCD3 and confirm the formability class with a sample before committing to a production run.
Electronics and small enclosures - electro-galvanized sheet offers a thin, very uniform coating that is easier to paint and print.
Outdoor structures with long service life - increase coating mass first, then consider an alloy or composite coating.
Frequently Asked Questions
Q: What does the D mean in DX51D, DX52D and DX53D?
The letter D indicates a grade intended for cold forming, and the number that follows rises with drawability. DX51D is commercial quality, DX52D drawing quality and DX53D deep drawing quality.
Q: What does Z120 mean on a galvanized sheet order?
Z120 means the total zinc coating mass on both surfaces is 120 g/m², roughly 60 g/m² per side. It is a coating-mass class, not a thickness of the steel sheet itself.
Q: Is EN 10327 still valid for DX51D sheet?
EN 10327 has been withdrawn and consolidated into EN 10346, which now covers continuously hot-dip coated steel flat products including the DX51D, DX52D and DX53D grades.
Q: Which spangle should be chosen for a painted product?
Zero or minimised spangle. Both give a smooth, uniform surface so the crystalline pattern cannot telegraph through a thin paint film. Regular or large spangle is normally reserved for unpainted applications.
Q: Can DX51D sheet be bent and profiled without cracking?
Yes. DX51D is commercial quality and handles simple bending and roll forming well, provided bend radii are not extremely tight. Severe draws require DX53D or a softer grade.
Q: How is the surface of galvanized sheet protected in transit?
Coils are wrapped with waterproof paper, strapped and carried on wooden pallets or in crates, and the surface may be passivated or oiled to limit white rust during sea transport and storage.

