Product
A galvanized coil is a steel strip that has been continuously passed through a molten zinc bath so that a layer of zinc adheres to the surface, protecting the steel from corrosion. Galvanized coils are divided into hot-rolled based and cold-rolled based products, and are used mainly in construction, household appliances, automobiles, containers and transport equipment; steel construction, automobile manufacturing and steel silo manufacturing are the largest consumers. The combination of strong corrosion resistance, good surface quality, ease of deep processing and economy explains why galvanized coil is one of the most traded steel flat products worldwide.
Applicable Standards
Z120g large spangle coil is supplied to the international standards that govern hot-dip zinc-coated sheet and strip. The most common references are JIS G3302 (hot-dip zinc-coated steel sheet and strip, Japan), EN 10346 (continuously hot-dip coated steel flat products for cold forming, Europe, the successor of the withdrawn EN 10327) and ASTM A653/A653M (hot-dip galvanized sheet, Americas). Grade options span SGCC and the SGCD drawing grades under JIS, DX51D and DX52D under EN 10346, and the corresponding CS/DDS classes under ASTM. The coating class Z120 (120 g/m2 total zinc on both surfaces) is specified together with the grade, thickness and spangle requirement.
Typical Coil Parameters
| Parameter | Value |
|---|---|
| Standards | JIS G3302 / ASTM A653M / EN 10346 |
| Grades | SGCC, SGCD1-SGCD3, DX51D, DX52D, DX53D |
| Thickness | 0.12-3.5 mm (0.3 mm in this case) |
| Width | 600-1250 mm (914, 1000, 1200, 1219, 1220, 1250 mm common) |
| Spangle | Regular, minimum, zero or large spangle |
| Zinc coating | 30-275 g/m2 (Z120 typical for this product) |
| Hardness | Soft (HRB60), medium (HRB60-85), full hard (HRB85-95) |
| Coil ID | 508 mm or 610 mm |
| Coil weight | 4-6 tons |
| Packing | Waterproof paper, steel strapping, seaworthy wooden case |
| Delivery | 7-15 days from order confirmation |
What Is a Zinc Spangle?
A zinc spangle, also called a zinc bloom, is the visible crystalline pattern on the surface of hot-dip galvanized sheet. It forms when the strip leaves the zinc bath and the liquid zinc layer solidifies naturally: zinc grains nucleate on the surface and grow as dendrites during cooling. The size and shape of the spangles are governed by the composition of the coating, particularly lead or antimony additions, and by the cooling rate and cooling method. When hot-dip galvanized sheet first appeared, mills could not control spangle size, and surfaces showed crystals of many sizes and shapes; this led to the early belief that only sheet with visible spangles was genuinely hot-dip galvanized. As manufacturing improved, process control allowed deliberate production of regular, minimum, zero and large spangles, and the international standards now define the accepted spangle classes.
Why Large Spangle Is Specified
Large spangle material is ordered mainly for aesthetic reasons. The bold crystalline pattern is considered attractive for outdoor and decorative applications such as fences, light poles, agricultural structures and some architectural panels, and it is also accepted where the surface will be painted or where appearance is not critical. Buyers should note that large spangles are associated with slightly thicker local zinc at crystal boundaries, which can matter for very tight bends; if the part is deep drawn, minimum or zero spangle is usually a safer choice because the surface is smoother and the coating more uniform in ductility.
Applications
At 0.3 mm gauge with Z120 coating, this coil is suited to light structural and semi-structural uses: roof sheeting and corrugated sheets, fencing and gates, cable trays, silo walls, air ducts and light frames, as well as general stamping parts in household appliances. For silo and roofing applications the soft or medium hardness temper is preferred so that the sheet can be roll-formed without cracking; full-hard temper is ordered when maximum stiffness at minimum gauge is required and no forming is planned.
Packaging and Shipping
Export coils are packed to survive sea transport: waterproof paper wrapped directly on the coil, steel strapping over protective edge rings, and a seaworthy wooden case or full wrap for the outer protection. Coil eyes are protected with plastic caps, and the packing list and mill certificate travel with the shipment. This packing standard prevents moisture ingress and edge damage during container transport, and is part of the reason galvanized coil arrives ready for immediate processing.
Frequently Asked Questions
What does Z120 mean on a galvanized coil? Z120 is the coating class: a nominal total zinc mass of 120 g/m2 on both surfaces combined, determined as the three-spot average per EN 10346. It corresponds to the metric expression of the same coating specified under JIS G3302 or ASTM A653.
What is the difference between large spangle and zero spangle? Large spangle shows big, visible zinc crystals and is chosen for appearance; zero spangle is produced by suppressing crystal growth with process control so the surface is smooth and uniform, preferred for painting and deep drawing.
Can 0.3 mm galvanized coil be used for roofing? Yes. 0.3 mm is a common gauge for corrugated roofing sheets in light structures, particularly when the coil is roll-formed into trapezoidal profiles. Confirm the grade and temper (soft or medium) with the profile supplier to match the design load.
Which standard replaces EN 10327? EN 10327 was withdrawn and its scope is covered by EN 10346, which now governs continuously hot-dip coated steel flat products for cold forming, including the DX51D-DX57D grades and Z coating classes.
How is coil hardness specified? Hardness is specified by temper: soft (about HRB60), medium (HRB60-85) or full hard (HRB85-95). Soft and medium tempers allow forming; full-hard coil is strong but brittle and unsuitable for bending.
Why does the zinc coating sometimes show white powder after storage? White rust is zinc hydroxide and zinc oxide that forms when moisture condenses on the surface, especially on closely packed coils. It is a storage condition issue, not a mill defect; keeping coils dry and well ventilated prevents it.

