Galvanized square and rectangular tube is made by applying a zinc coating to a hollow section, and the coating is what widens the application range of the section far beyond that of bare tube. The two processes sold commercially as hot galvanizing and cold galvanizing differ in how the zinc is bonded to the steel, and that difference decides where each one may be used and how long it will last.
What Hot Galvanizing and Cold Galvanizing Actually Are
Hot-dip galvanizing immerses the finished steel in molten zinc at about 445 to 465 degrees Celsius. The zinc reacts with the iron at the surface to form a sequence of zinc-iron alloy layers, so the coating is metallurgically bonded to the steel and cannot be peeled away. The process is standardised by ISO 1461, by ASTM A123/A123M for fabricated products, and by GB/T 13912. Cold galvanizing, also called cold-applied galvanizing or zinc-rich coating, is a paint-like product containing a high proportion of zinc dust in a binder. It is applied at ambient temperature by brush, roller or spray, and it protects the steel by sacrificial action without forming any alloy layer at the interface.
Process Comparison
The practical consequences of the two processes are summarised below. The comparison explains why a galvanized tube frame and a tube frame repaired on site rarely use the same coating technology.
| Property | Hot-dip galvanizing | Cold-applied zinc-rich coating |
|---|---|---|
| Bonding mechanism | Metallurgical zinc-iron alloy layers | Mechanical bond through the binder |
| Typical thickness | 45 to 85 microns, graded by steel thickness | 40 to 80 microns dry film, often two coats |
| Adhesion and abrasion | Very high, resists peeling and impact | Good, sensitive to surface preparation |
| Site work | Shop process requiring a galvanizing bath | Can be applied on site at any stage |
| Typical role | New structural frames, tube and sections | Repair of damaged coatings and welds |
| Reference standards | ISO 1461, ASTM A123/A123M, GB/T 13912 | Zinc-rich coating systems such as SSPC Paint 20, ISO 12944 paint systems |
Applications in Construction, Curtain Wall and Steel Structures
Construction remains the largest outlet. Galvanized square and rectangular tube is used for curtain wall and glass curtain wall support frames, where the tube is visible and the coating must combine corrosion resistance with a uniform appearance. In steel structure engineering the same sections form columns, bracing, purlins and secondary framing, and the galvanized finish allows the structure to be erected without the site painting that an uncoated frame would require. Building and industrial construction also consumes the sections as handrail, guard rail, support legs and platform framing, where the closed hollow section provides a high stiffness-to-mass ratio and the zinc coating resists atmospheric attack on exposed edges.
Applications in Energy, Transport and Industry
Solar power generation is now one of the fastest-growing applications. Mounting brackets and tracker frames are exposed for decades to rain, dust and temperature cycling, and galvanized tube provides the corrosion margin without the maintenance cost of painted steel. Power engineering and power plant work use galvanized sections for cable supports, equipment frames, walkway structures and chimney supports, where hot-dip galvanizing tolerates elevated temperatures better than most paint systems.
In shipbuilding and marine outfitting the coating protects internal framing and deck equipment from salt-laden air, while in transport the sections appear in automobile chassis, trailer frames, bus body structures and airport installations such as baggage-handling supports and signage gantries. Machinery manufacturing uses galvanized rectangular tube for agricultural machinery frames, chemical machinery supports and general industrial fabrications, where wash-down, fertiliser or chemical splash makes a bare steel frame unacceptable.
How the Application Decides the Coating Specification
The environment and the component thickness together fix the required coating. ISO 1461 ties the minimum zinc coating thickness to the steel thickness, because thicker steel cools more slowly and reacts with more zinc:
| Steel thickness | Minimum local coating thickness | Typical environment |
|---|---|---|
| Under 1.5 mm | About 45 microns | Dry rural and indoor service |
| 1.5 to under 3 mm | About 45 microns locally, higher average | Urban and rural outdoor exposure |
| 3 to under 6 mm | About 55 microns locally, higher average | Industrial and coastal atmospheres |
| 6 mm and over | About 70 microns locally, higher average | Severe coastal and chemical service |
Two design decisions change the outcome more than the average thickness figure. First, drainage and venting: a closed tube that traps water or that cannot release molten zinc during dipping will fail at the uncoated internal surface. Second, fabrication sequence: welding should be completed before galvanizing, and any weld or cut made afterwards must be repaired with a zinc-rich coating. Where the corrosivity category of the site is severe, a duplex system of galvanizing plus a compatible top coat is commonly specified to extend the interval before first maintenance.
FAQ
Q: Is cold galvanizing as durable as hot-dip galvanizing?
No. Cold-applied zinc-rich coatings are mechanically bonded and are best used for repair, touch-up and site work, while hot-dip galvanizing forms zinc-iron alloy layers and is the specified coating for new load-bearing structures in outdoor or aggressive environments.
Q: Where is galvanized square and rectangular tube used?
Typical uses are curtain wall and glass curtain wall framing, steel structure engineering, machinery manufacturing, shipbuilding, solar power mounting brackets, power engineering and power plants, agricultural and chemical machinery, automobile chassis and airport installations.
Q: How thick is a hot-dip galvanized coating?
ISO 1461 sets a minimum local coating thickness that depends on steel thickness, from about 45 microns for sections below 1.5 mm to about 70 microns for sections 6 mm and heavier, with higher average values required in each case.
Q: Can galvanized tube be welded?
Yes, but the zinc coating should be removed from the weld zone before welding, welding fume must be controlled, and the weld and heat-affected zone must be recoated with a zinc-rich product afterwards.
Q: What determines the service life of galvanized tube?
Coating thickness and the corrosivity of the environment. Rural atmospheres are the mildest, while coastal salt spray, industrial pollution and chemical splash consume the coating far more quickly. Design details that allow water to drain extend life as much as extra coating does.
Q: Does galvanizing change the mechanical properties of the tube?
The hot-dip process uses a short thermal cycle below 500 degrees Celsius, which does not alter the strength of normal structural tubing. Thin-wall or strongly asymmetric sections can distort during dipping, so allowance should be made in the fabrication drawings.

