Where DC01 and DC04 Sit in the EN 10130 System
DC01 and DC04 are drawing quality cold rolled steels from EN 10130, the European standard for cold rolled low carbon steel flat products for cold forming. They belong to a ladder of grades whose formability increases from DC01 through to DC06, and each step trades strength for the ability to deform without splitting. Both grades are supplied annealed and skin passed, which gives a recrystallised structure, a defined surface finish and consistent flatness across the coil.
The designations that preceded them are still seen on drawings and old tooling documentation. St12 of DIN 1623 was replaced by DC01 when DIN 1623 was superseded by DIN EN 10130, and on the same basis ST13 became DC03 and ST14 became DC04. Anyone reading a legacy drawing should translate the ST designation into the DC equivalent rather than assuming the grade has changed in performance.
Cross-Standard Equivalents
DC01, material number 1.0330, appears under different names in the major national systems and under trade names in the marketplace.
| System | Designation for DC01 | Designation for DC04 |
|---|---|---|
| European, EN 10130 | DC01, material number 1.0330 | DC04, deep drawing quality |
| Former German, DIN 1623 | St12 | St14 |
| Japanese, JIS G3141 | SPCC | SPCF, deep drawing class |
| American, ASTM A1008 | CS Type B, commercial steel | DDS, deep drawing steel |
| Chinese practice | Commercial quality cold rolled sheet in the Q195 to Q215 strength class | Deep drawing quality cold rolled sheet |
| British trade name | CR4 | Deep drawing class of the same cold reduced family |
These equivalences are functional rather than clause by clause identical, because each system defines its own chemical limits, thickness tolerance tables and surface classes. An order should therefore name the standard together with the grade, which is the only way to make tolerances and test certificates unambiguous.
Chemical Composition
Formability in these grades comes from keeping carbon and manganese low and from controlling residual elements that raise strength and increase springback.
| Element | DC01, maximum | DC03, maximum | DC04, maximum |
|---|---|---|---|
| Carbon | 0.12 % | 0.10 % | 0.08 % |
| Manganese | 0.60 % | 0.45 % | 0.40 % |
| Phosphorus | 0.045 % | 0.035 % | 0.030 % |
| Sulphur | 0.045 % | 0.035 % | 0.030 % |
The composition of DC04 is deliberately balanced: a carbon maximum of 0.08 percent and a manganese maximum of 0.40 percent keep the annealed matrix soft and ductile, while low residuals reduce work hardening sensitivity and springback. Low yield strength also lowers the punch force required and improves die filling, which is what makes complex deep drawn parts possible at production rates.
Mechanical Properties and Formability
| Grade | Yield strength Re (MPa) | Tensile strength Rm (MPa) | Elongation A80 (%) | Forming behaviour |
|---|---|---|---|---|
| DC01 | 280 maximum | 270–410 | 28 minimum | Bending, coining, beading, shallow drawing |
| DC03 | 240 maximum | 270–370 | 34 minimum | Deep drawing, difficult profiling |
| DC04 | 210 maximum | 270–350 | 36 minimum | Severe deep drawing, complex stamped parts |
DC04 is a deep drawing steel with excellent drawing properties under all types of deformation, and it also carries a higher plastic strain ratio and a higher strain hardening exponent than DC01, which together flatten the strain distribution across a pressed panel. In routine terms, the lower yield strength means less punch force, the higher elongation means more available stretch before failure, and the better normal anisotropy means the wall of a drawn cup thins more evenly.
Grade Selection in Practice
Choose DC01 for simple forming operations such as bending, coining, beading and shallow drawing, and where material cost is the deciding factor.
Choose DC03 where the part needs moderate drawing and a tighter profile than DC01 can deliver.
Choose DC04, or a grade above it, for deep drawn and complex stamped parts such as automotive and appliance components.
The staircase from DC01 to DC06 provides increasing formability at increasing cost, so the softest grade that the part actually needs is the correct commercial choice.
Thicker material tolerates tighter bend radii for the same grade, and thinner material needs the more ductile grade to reach the same geometry.
Fabrication and Storage Notes
Both grades weld readily. Thin sheet in the DC family is commonly joined by resistance spot welding and by pulsed MIG welding at currents in the region of 120 to 150 A, where burn through is avoided without losing penetration. Springback is modest compared with higher strength steels but still has to be compensated in the tool, and the compensation is larger for DC01 than for DC04 because its yield strength is higher. Coils and sheets should be kept dry and ventilated, clear of the floor, and stacked only to a sensible height so that surface deformation and scratches do not appear before the material reaches the press.
Frequently Asked Questions
Q: What is DC01 steel equivalent to?
DC01, material number 1.0330, is the grade that replaced ST12 when DIN EN 10130 superseded DIN 1623. It is functionally similar to SPCC of JIS G3141, ASTM A1008 CS Type B and commercial quality cold rolled sheet in the Q195 to Q215 strength class.
Q: Is DC01 the same as CR4?
Yes. CR4 is the British trade description of the same cold reduced mild steel, where CR stands for cold reduced and 4 indicates the quality level.
Q: What is the composition of DC04?
DC04 is a low carbon steel with a carbon maximum of about 0.08 percent and a manganese maximum of about 0.40 percent, with phosphorus and sulphur held to low maximums to preserve ductility.
Q: What is DC04 used for?
Deep drawing and high forming applications such as complex automotive and appliance stampings, where the part geometry demands the maximum available stretch before fracture.
Q: How do DC01 and DC04 differ?
DC04 has lower carbon, a lower permitted yield strength and a higher minimum elongation, so it can be drawn more deeply than DC01, and it costs more as a result.
Q: What replaced the ST designations?
DIN EN 10130 replaced DIN 1623, so ST12 became DC01, ST13 became DC03 and ST14 became DC04.
Q: Are the cross-standard equivalents interchangeable without testing?
They are functionally similar rather than identical, because each system has its own tolerance and surface clauses, so the applicable standard should always be stated on the purchase order.

