Cold Rolled Galvanized Steel Sheets and Coil: Grades, Coatings and Uses

Sep 02, 2025 Leave a message

Overview of Cold Rolled Galvanized Steel Sheets and Coil

Cold rolled galvanized steel sheet and coil start as hot rolled substrate that is cold reduced to the required gauge on a tandem mill and then annealed to restore formability. The annealed strip is zinc coated by one of two routes: continuous hot dip galvanizing, which builds a coating of roughly 60-275 g/m2, or electrogalvanizing, which deposits a thinner and more uniform layer that takes paint very well. Material is supplied as coil, as cut to length sheet and as slit strip, and the same coil can be delivered with an oiled, dry or passivated surface.

Grade Range: DC01 to DC04 and Their Equivalents

Grade Key characteristic Typical use
DC01 General purpose forming grade, designation 1.0330 Bending, roll forming, general panels
DC02 Drawing quality Moderate drawing, shallow pressed parts
DC03 Deep drawing quality Deeper drawn components
DC04 Deep drawing steel with high formability, carbon max 0.08 % and manganese max 0.40 % Parts with high forming requirements

The DC series is defined in EN 10130, which also replaced the withdrawn DIN 1623 designation St12 by DC01. In trade usage DC01 mild steel is sometimes referred to as CR4, and in some markets material is still ordered under the older St12 label, so an equivalent grade table is useful when a drawing or purchase specification was written years ago.

Zinc Coating Designations and Standards

Hot dip galvanized: EN 10346 covers continuously hot dip zinc coated flat products with designations such as Z100, Z140, Z225 and Z275, where the number is the total coating mass in g/m2 on both faces. Z275 corresponds to a nominal zinc thickness of about 20 µm per side.

JIS G 3302: the Japanese standard for hot dip zinc coated steel sheet, with commercial quality SGCC among its most widely traded designations.

Electrogalvanized: EN 10152 designates electrogalvanized material such as DC01+ZE, and JIS G 3313 covers the SECC designation family with very uniform, thin coatings.

Base steel: the cold rolled substrate behind the coating is normally specified to EN 10130 for DC grades or JIS G 3141 for SPCC.

Formability and Fabrication

Zinc is softer than steel, so the coating acts as a partial lubricant during forming, but forming tools should still be kept clean and a suitable drawing lubricant used. Sharp bend radii, heavy ironing and severe stretch forming can damage the coating, so the forming route is matched to the grade: DC01 for simple bends and roll forming, DC03 for deeper draws, and DC04 where the shape demands the highest formability within the family. Welding is straightforward with spot and seam processes, and laser or arc welding can be used where joints are prepared for the zinc vapour that forms during fusion. Cut edges are protected by the sacrificial action of the surrounding zinc.

Typical Applications

Roof and wall cladding, purlins and general building profiles.

Ventilation and air conditioning ductwork.

Appliance cabinets, backs and internal panels.

Automotive inner panels and brackets.

Electrical enclosures and cable trays.

Containers, solar panel frames and general light fabrication.

Frequently Asked Questions

Q: What is DC01 steel equivalent to?
DC01 is also designated 1.0330, and it is the EN 10130 grade that replaced the withdrawn DIN 1623 designation St12. Comparable national grades include JIS SPCC and GB commercial quality cold rolled sheet.

Q: Is DC01 the same as CR4?
CR4 is a trade name commonly used for DC01 mild steel cold reduced sheet, so the two are treated as the same material in normal commercial practice, with thicknesses typically stocked between 0.9 mm and 3 mm.

Q: What is grade DC04?
DC04 is a deep drawing steel of the DC family with excellent deep drawing properties under all types of deformation, making it suitable for parts with high forming requirements.

Q: What is the carbon content of DC04?
DC04 is a low carbon steel with a maximum carbon content of about 0.08 % and a maximum manganese content of about 0.40 %, balanced to give the required mechanical properties.

Q: Which standard applies to the zinc coating?
Hot dip zinc coated cold rolled sheet is covered by EN 10346 and JIS G 3302, while electrogalvanized material is covered by EN 10152 and JIS G 3313.

Q: Why is the coil supplied oiled?
A light oil film is applied to protect the bright cold rolled surface from moisture and staining during storage and transport, and it is normally removed before painting.