SPCC and DC01: Two Names for Cold Rolled Low Carbon Sheet
SPCC belongs to the cold-rolled steel sheet and strip family of JIS G 3141, while DC01 is the corresponding European grade defined in EN 10130 and known historically as material 1.0330. Both describe a low-carbon, unalloyed sheet supplied for cold forming rather than for structural load carrying, and both are normally delivered with an annealed and skin-passed surface that is flat, consistent in thickness and ready to paint or to feed into a forming press.
The comparison matters because the two systems are used side by side in the market. A buyer quoting SPCC and a supplier quoting DC01 may in fact be discussing the same class of product, so the useful question is not which name is correct but which properties, tolerances and surface finish the application actually needs.
What 1 mm Thickness and 19 Gauge Mean in Practice
Thickness is quoted metrically in most cold-rolled specifications. A 1 mm nominal thickness is the standard metric call-off for this class of sheet and is the value that appears on the mill certificate and in the tolerance tables. In trade and legacy documents the same sheet is also described as 19 gauge. Gauge numbers are a legacy designation rather than a metric unit, so the gauge figure should always be read together with the metric thickness that the supplier is actually able to certify. For process planning, work from the metric value and treat the gauge label as a familiar shorthand.
Nominal thickness - 1 mm, subject to the tolerance band of the applicable standard.
Gauge shorthand - 19 gauge in the legacy system still used in some markets.
Supplied form - coil for continuous lines, or cut lengths where a press line prefers flat sheets.
DC01 and DC04: Two Levels of Formability
DC01 and DC04 are both cold-rolled, unalloyed quality steels from the same European family, but they sit at different points on the formability scale. DC01 is the general grade for ordinary cold forming such as bending, light drawing and roll forming. DC04 is a deep-drawing grade with better ductility and lower carbon and manganese levels, so it tolerates more severe deformation before it tears. The two grades are often stocked side by side, and the decision between them is driven by the severity of the forming operation rather than by thickness.
| Grade | Forming role | Carbon (max) | Manganese (max) |
|---|---|---|---|
| DC01 | General cold forming | 0.12 % | 0.60 % |
| DC04 | Deep drawing, higher ductility | 0.08 % | 0.40 % |
The table shows the direction of travel: as drawing severity rises, allowable carbon and manganese fall, because lower residuals improve elongation and the uniformity of the deformation. The values shown are typical specification maxima, and the limits that apply to a given order are always those of the standard edition named on the mill certificate.
Surface Finish, Flatness and Coil Handling
Cold-rolled sheet of this class is normally delivered with a matte or a bright finish depending on the skin-pass rolls. Either finish is acceptable for painting and forming, but consistency within a coil and from coil to coil is what protects a paint line or a forming press from having to change its settings. Flatness and thickness uniformity matter equally: a coil that averages 1 mm but varies across the width will produce inconsistent parts even though the nominal call-off is met.
Handling also deserves attention. This is a low-carbon, relatively soft sheet, so it deforms readily under mishandling. Coils should be stored on saddles or a flat base, lifted with the correct sling arrangement and uncoiled under controlled tension so that the strip is not stretched or marked before it reaches the tooling.
Where These Grades Fit
Typical uses for SPCC and DC01 at around 1 mm thickness include appliance panels, enclosure bodies, shelving, automotive interior brackets, furniture components and the many parts where a flat, formable, paintable sheet is required without a structural duty. When the application needs more strength at the same thickness, a coated or micro-alloyed variant is normally chosen instead of a heavier gauge, because added thickness costs weight while a higher-strength grade does not.
Where corrosion protection is the priority, the same substrate can be supplied with an electrolytic or a hot-dip zinc coating, which is where coated grade names such as SGCC and SECC enter the description. The underlying steel and its forming behaviour remain those of the SPCC or DC01 substrate.
Frequently Asked Questions
Q: Is DC01 the same as CR4?
They describe the same class of cold-reduced drawing-quality sheet. CR4 is an older shorthand used in some markets, while DC01 is the current European designation under EN 10130; a substitute should be accepted on the strength of certified properties rather than on the label.
Q: Can SPCC be used where DC01 is specified?
Often yes, because both are low-carbon cold-rolled forming grades, but the substitution must be checked against the certified chemical and mechanical values, the surface finish and the tolerance requirements of the application.
Q: Does 1 mm always equal 19 gauge?
No. Gauge numbers come from a legacy system in which the equivalent metric thickness differs between sheet and strip conventions. Work from the metric thickness and treat the gauge value as a convenience label only.
Q: Which grade is more formable, DC01 or DC04?
DC04. It is a deep-drawing grade with lower carbon and manganese maxima and higher ductility, so it survives deeper drawing operations than DC01 without tearing.
Q: Is DC01 supplied galvanized?
DC01 describes the bare cold-rolled substrate. When the same steel is supplied zinc coated, the coating is specified separately, for example as a hot-dip or electrolytic coated product, and the coating requirements come from the relevant coating standard.
Q: What tolerance applies to a 1 mm cold rolled coil?
The tolerance band is set by the product standard named on the certificate and varies with width and with whether the product is ordered as sheet or coil, so the applicable edition should be confirmed for each order.

