What SPCC Covers and What It Does Not
SPCC is the commercial-quality grade of cold-reduced carbon steel sheet and strip in JIS G 3141. It is an uncoated product: the surface protection, if any, is a film of rust-preventive oil rather than a metallic coating, and any zinc or organic coating is a separate operation carried out on the same coil or on parts cut from it. Within JIS G 3141 the series continues upward through SPCD for drawing and SPCE for deep drawing, so SPCC is the grade chosen when the forming duty is light and the requirement is a clean, dimensionally accurate, weldable surface.
The composition ceiling of SPCC is carbon 0.15% maximum, manganese 0.60% maximum, phosphorus 0.100% maximum and sulphur 0.050% maximum, with a minimum specified tensile strength of 270 MPa. Those limits are deliberately looser than the European DC grades, which is why SPCC converts cheaply into brackets, ducts, panels, furniture frames and light stampings but is not the grade to specify for a difficult deep draw.
Thickness Range and How It Is Set
Cold-reduced SPCC coil is traded from around 0.12 mm at the thin end to 2.5 mm at the heavy end. Thin gauges below roughly 0.35 mm are ordered for precision parts such as closures, shielding and small enclosures, and they demand a levelled, well-packed coil because the material has little stiffness and will crease if it is handled carelessly. Mid-range gauges from 0.5 mm to 1.0 mm cover most stamping and roll-forming work. Above 1.5 mm the coil is used for structural brackets, chassis components and heavier formed parts.
Thickness tolerances for cold-rolled uncoated and electrolytically coated flat products are specified in EN 10131, in a normal class and a tighter class, and the tolerance band widens with nominal thickness and with coil width. For the thinnest gauges, a formal agreement rather than the standard table is normally used, because the achievable band is dominated by rolling and levelling practice. The practical rule is to state the functional thickness for the part - the value at which the tool was validated - and to accept the tolerance class that brackets it, rather than to order the thinnest gauge that will pass a spot check.
Standard Widths, Slitting and Edge Condition
SPCC coil is produced at standard mill widths and then slit to the order width, so the available range runs from about 600 mm to 1500 mm. The four widths quoted most often are 1000 mm, 1219 mm, 1220 mm and 1250 mm: the 1219 mm figure is the imperial 48 inch master width carried over from older lines, 1220 mm and 1250 mm are the metric equivalents used on newer mills, and 1000 mm is the common narrow master for small presses.
| Parameter | Common range | Typical ordering note |
|---|---|---|
| Thickness | 0.12 - 2.5 mm | State functional thickness and tolerance class |
| Width | 600 - 1500 mm | Master widths 1000 / 1219 / 1220 / 1250 mm before slitting |
| Coil inner diameter | 508 mm, 610 mm | Match to the uncoiler mandrel |
| Coil mass | 3 - 15 t | Limited by crane and decoiler capacity |
| Edge condition | Mill edge or trimmed | Trimmed edge for exposed or roll-formed parts |
Slitting quality matters as much as the nominal width. A properly set slitter produces a square, burr-free edge with a defined camber limit; a worn slitter produces a turned-down edge and a burr line that will show as a scratch on the finished part and will notch the strip under tension. Where the part is roll-formed or press-fed, add the burr direction and the camber limit to the specification rather than accepting whatever the slitter produces.
Coil Identification and Delivery Documentation
Each coil should travel with a tag and a certificate that allow it to be traced back to the cast. The minimum data set is grade, heat number, coil number, nominal thickness and width, coil mass, inner diameter, date of production and the applicable standard. Where the part is safety-related or supplied into an audited chain, an inspection document type 3.1 to EN 10204 is normally requested so the chemistry and tensile results are tied to the specific heat rather than to a general mill report.
Marking practice is equally important at the coil end. Coils are marked on the outer wrap and on an inner tag; if the outer wrap is removed on site, the inner identification is all that is left. Buyers taking delivery of mixed heats should insist that the coil number is also written on the inner tag and that the heat number appears in the same position on every coil, so a partial consumption can still be traced.
Storage, Handling and Rust Prevention
Uncoated cold-reduced steel has no alloying protection and will rust wherever moisture condenses on it. Store coils and sheets in a dry, ventilated building, keep them clear of the floor on timber or rubber bearers, and never leave them standing in a stack against an outside wall where the temperature swings. Avoid contact with acids, alkalis and salt-bearing dust, and do not store near pickling or plating lines.
The rust-preventive oil applied at the mill will protect a coil for a limited period in a dry indoor store; a paper interleaf or a shrink-wrapped coil extends that period considerably, and it should be specified for sea freight and for long site storage. Coils stacked too high will deform at the bottom, and coils lifted with a bare chain will be damaged at the edge - use a spreader or a proper C-hook. Where the coil is cut into sheets on site, re-stack the sheets on a flat pallet and re-cover them, because freshly cut edges are the first place where corrosion starts.
Frequently Asked Questions
Q: What thickness range is available in SPCC cold-rolled coil?
A: Supply covers roughly 0.12 mm to 2.5 mm; very thin gauges require care in handling and packing, while gauges above 1.5 mm are used for heavier formed parts.
Q: Which widths are standard?
A: Mill widths of 1000 mm, 1219 mm, 1220 mm and 1250 mm are the most common, and the delivered width range after slitting is about 600 mm to 1500 mm.
Q: What tolerances apply to thickness and width?
A: Thickness and shape tolerances for cold-rolled uncoated flat product are taken from EN 10131, chosen in the normal or tighter class; slitting width tolerance is normally fixed by agreement with the processor and tightened for precision blanks.
Q: How long does the coil resist rust as delivered?
A: A coil with a standard rust-preventive oil film will hold in a dry indoor store for a limited period only; a film coating or a paper interleaf with proper wrapping extends that period substantially and should be specified for sea freight.
Q: Can SPCC be stretched or deep drawn?
A: It handles light stretching and shallow draws. For repeated or severe drawing, move to SPCD or SPCE, or to an equivalent EN 10130 grade such as DC03 or DC04.
Q: Is SPCC the same as a galvanized coil?
A: No. SPCC is uncoated cold-reduced steel. The zinc-coated equivalents are designated in the hot-dip and electrolytic coating standards and must be ordered separately.
Q: What should be checked on arrival?
A: Grade and standard on the certificate, heat and coil number against the tag, thickness and width at several points along the coil, edge condition, and the presence and continuity of the oil film.

