Cold Rolled Steel Coils Compared: SPCC, SPCD, SPCE and SPCF

Sep 12, 2025 Leave a message

How the JIS G 3141 Cold Rolled Grades Differ

JIS G 3141 arranges cold rolled carbon steel sheet and strip into a formability ladder that runs from commercial quality through drawing and deep drawing qualities. Four designations appear most often on coil and sheet orders: SPCC, SPCD, SPCE and SPCF. Choosing between them is a balance of forming severity, surface requirement and cost, and the grade named at the ordering stage fixes the chemistry and the rolling route that the mill will use.

All four are low carbon, uncoated cold rolled products. They share the same clean surface, tight thickness tolerance and good weldability; what changes is how far the steel can be stretched into a die before it tears or thins excessively.

SPCC: General Purpose Commercial Quality

SPCC is cold rolled carbon steel sheet and coil for general purposes. It offers good stamping and welding performance, excellent surface quality and high dimensional accuracy, and it is the base material from which electrolytic zinc coated and hot dip galvanised sheet are produced. Typical applications include automotive components, home appliances, metal products and precision electronics.

Because it is the entry grade, SPCC is also the cheapest of the four and the one most widely stocked. It suits parts formed by bending, roll forming and shallow stamping rather than by deep drawing.

SPCD: Drawing Quality

SPCD is the drawing quality grade of the same series. It provides better stamping performance than SPCC, with improved deep drawing behaviour and resistance to strain ageing, achieved through closer control of carbon and nitrogen in the melt. Parts formed from it hold their shape without the orange peel surface that coarser grades can show after deformation.

It is used for components that need more than a simple bend but do not demand the full drawability of the upper grades, such as automotive outer parts and appliance housings.

SPCE: Deep Drawing Quality

SPCE is the deep drawing grade. Its chemistry and grain structure are controlled so the steel flows into complex shapes under high tensile demand while keeping wall thickness even around radii. It is suitable for parts formed by deep drawing processes, including automotive interior components and the internal structural parts of home appliances.

Where a single press stroke forms several bends together with a shallow cup, SPCE generally gives a more reliable result than SPCD, at a higher material cost.

SPCF: Grades beyond SPCE

SPCF continues the same ladder and is quoted for parts that require more severe forming than the deep drawing grade can sustain, such as large drawn enclosures, deep bowls and components with very tight corner radii. It is supplied to tighter chemistry limits than SPCE, with low carbon and low residual content that keeps the forming limit high.

SPCF is ordered far less often than the other three grades and is normally specified only when a forming analysis shows that SPCE would be marginal. Note that coated products belong to different standards altogether: hot dip galvanised coil is specified to JIS G 3302, and the uncoated substrate beneath the coating is still a cold rolled grade.

Grade Comparison at a Glance

Grade Formability class Typical use
SPCC Commercial quality General stamping, bending and welding; base for coated coil
SPCD Drawing quality Stamped and moderately drawn parts, appliance housings
SPCE Deep drawing quality Complex deep drawn parts, automotive interiors, appliance internals
SPCF Severe deep drawing quality Deep bowls and enclosures formed at the material forming limit

Coil and Sheet Supply Specifications

The dimensional data below reflects the uncoated cold rolled product family. A coil ordered as 0.60 mm thickness by 1120 mm width, for example, can be produced in any of the four grades, with the grade chosen to suit the forming operation rather than the size alone.

Item Value or range
Product Cold rolled steel coil, sheet, strip and plate, uncoated
Grades SPCC, SPCD, SPCE, SPCF (JIS G 3141); DC01 to DC04 equivalents in EN 10130
Thickness 0.125 to 3.0 mm
Width 600 to 1250 mm
Coil inner diameter 508 mm or 610 mm
Coil weight 3 to 8 MT
Surface condition Annealed, skin passed and oiled; chromate passivation where specified
Dimensional tolerance According to EN 10131 for cold rolled flat products
Packing Standard export packing with edge protection and moisture barrier

Selecting the Right Grade

Selection should start from the forming severity shown on the part drawing. If the component only bends or roll forms, SPCC is sufficient. If it is drawn, move up to SPCD or SPCE, and reserve SPCE or SPCF for parts where thinning around radii is the limiting factor. Surface requirement matters as well: a visible face usually needs a surface quality class that restricts minor defects, while a hidden reinforcing part can accept a standard finish. Finally, confirm that the mill can roll the chosen grade in the requested thickness and width, because the upper drawing grades are not produced in every size combination.

Frequently Asked Questions

Q: Which grade is best for general stamping?
SPCC is the general purpose choice, offering good stamping and welding performance together with excellent surface quality and high dimensional accuracy.

Q: What does the D in SPCD indicate?
It marks drawing quality. SPCD stamps and draws better than SPCC and is produced with ageing resistance so its properties remain stable during storage and forming.

Q: When is SPCE preferred over SPCD?
When the part needs genuine deep drawing with high tensile demand and complex shapes, such as appliance internals and automotive interior components.

Q: Is SPCF part of JIS G 3141?
Yes. SPCF sits above SPCE in that standard and is intended for more severe drawing than the deep drawing grade can sustain.

Q: Can the same grades be used for coated coil?
The coating standards are separate: hot dip galvanised coil is specified to JIS G 3302, and the property requirements of the coating product take precedence over the substrate grade.

Q: What thickness and width are available?
Typically 0.125 mm to 3.0 mm thickness and 600 mm to 1250 mm width, supplied on 508 mm or 610 mm bores in coils of 3 to 8 MT.