The DX Family: One Standard, Five Formability Levels
EN 10346 defines continuously hot-dip zinc-coated steel strip and sheet for cold forming as the DX51D-to-DX57D family. The number after DX rises with formability: DX51D for simple bending, DX52D for light profiling, DX53D for drawing, DX54D for deep drawing, and DX56D/DX57D for very deep and extreme forming. All grades can be ordered with the +Z zinc coating (or +ZA zinc-aluminium, +AZ aluminium-zinc and +AS aluminium-silicon). Choosing between DX53D and DX54D is therefore a question of how deep and how complex the draw is, balanced against cost, because the softer, more formable grades carry a price premium.
Chemical Composition
All DX grades are low-carbon steels with tight control of residuals so that formability is not lost to hard phases. For DX54D the maximum contents are typically C 0.12%, Si 0.50%, Mn 0.60%, P 0.10%, S 0.045% and Ti 0.30%, with aluminium added for deoxidation. DX53D follows the same philosophy with slightly higher permitted carbon and manganese. The low carbon and controlled micro-alloying keep the material soft after annealing, which is what gives the high elongation values below.
Mechanical Properties: DX53D vs DX54D
Per EN 10346 the guaranteed values for thickness 0.7-2.0 mm position the two grades clearly apart. DX53D+Z typically shows Rp0.2 of 140-260 MPa, Rm of 270-390 MPa and minimum elongation A80 of 30%. DX54D+Z is softer and more ductile: Rp0.2 of 120-220 MPa, Rm of 260-350 MPa and minimum A80 of 36%. The lower yield point of DX54D means the material starts to flow under lower stress, and the higher elongation means it can stretch further before necking and fracture. In practice this is the difference between a part that draws in one deep operation and one that cracks at the corner radius.
| Grade (+Z) | Rp0.2 (MPa) | Rm (MPa) | A80 min. (%) | Forming level |
|---|---|---|---|---|
| DX51D | 140-300 | 270-500 | 22 | Bending, simple forming |
| DX52D | 140-300 | 270-420 | 24 | Light profiling |
| DX53D | 140-260 | 270-390 | 30 | Drawing |
| DX54D | 120-220 | 260-350 | 36 | Deep drawing |
| DX56D | 120-180 | 260-350 | 39 | Very deep drawing |
Production Route: From Slab to Coated Coil
Understanding the process explains why DX54D behaves as it does. The steel is smelted and refined, then continuously cast into slabs. Slabs are reheated and hot rolled at around 1200 C to strip, cooled and coiled. The hot-rolled strip is pickled to remove scale and cold rolled to final gauge, which work-hardens the steel. Recrystallisation annealing at roughly 700-800 C restores the soft, ductile ferrite structure that gives DX54D its elongation. The strip then enters the hot-dip galvanizing line, where it is cleaned, heated, and passed through a molten zinc bath at about 450-460 C; gas knives control the coating mass to the ordered Z-class, and the strip cools to form the final spangle structure before recoiling.
Grade Equivalents Across Standards
Buyers compare EN grades with Japanese and American designations when sourcing internationally. In JIS G3302, SGCC covers general use, while SGCD1-SGCD4 are drawing grades with increasing formability; the deeper SGCD grades are the practical equivalents of DX53D/DX54D. For structural rather than forming applications, JIS offers SGC340-SGC510. In ASTM A653, the CS (commercial steel), DDS (deep drawing steel) and EDDS (extra deep drawing steel) classes span a similar range, with DDS/EDDS closest in intent to DX53D/DX54D. Equivalence is never exact: always validate against the mill certificate and the governing standard of the destination market.
| Formability intent | EN 10346 | JIS G3302 (typical) | ASTM A653 |
|---|---|---|---|
| General use | DX51D+Z | SGCC | CS Type B |
| Drawing | DX53D+Z | SGCD1/SGCD2 | DDS |
| Deep drawing | DX54D+Z | SGCD3 | DDS/EDDS |
How to Choose Between DX53D and DX54D
Use DX53D+Z when the part is drawn with moderate depth, generous radii and one or two operations, for example brackets, lamp housings and light appliance panels. Move to DX54D+Z when the draw is deep, the corner radius is tight, or a second forming operation happens after drawing, such as oil-filter housings, wheel discs and complex automotive panels. If the coating mass is also high, remember that thick zinc layers have limited ductility; for severe draws, either reduce the Z-class or confirm the minimum bend and draw performance with the supplier before production.
FAQ
What does DX54D+Z stand for?
DX indicates cold-forming steel for continuous hot-dip coating per EN 10346, 54 is the formability class, D stands for steel for cold forming, and +Z means a zinc coating. A coating class such as Z275 follows in the full designation, e.g. DX54D+Z275.
Is DX54D stronger than DX53D?
No. DX54D is softer and more formable: its yield range is lower (120-220 MPa vs 140-260 MPa) and its minimum elongation is higher (36% vs 30%). Strength is sacrificed deliberately to gain drawability.
Can DX54D be used for structural applications?
Not as a first choice. DX54D is designed for forming, not load bearing. For structural members use the S-series of EN 10346 such as S350GD or S450GD, which guarantee much higher yield strength.
What coating classes are available for DX54D?
EN 10346 allows zinc coatings from about Z100 up to Z450 depending on thickness, with Z180, Z200, Z225 and Z275 common for automotive and appliance parts. The coating class is chosen separately from the grade.
Does DX54D weld well?
Yes, the low carbon content gives excellent spot weldability, which is why it is used in automotive body parts. Resistance spot welding is standard; for arc welding of galvanized product, remove the zinc at the joint and control fume as with any coated steel.
How is elongation A80 measured?
A80 is the percentage elongation after fracture measured on a proportional test piece with an original gauge length of 80 mm, per the tensile test standard EN ISO 6892-1. The minimum value in EN 10346 depends on the grade and the thickness range.

