What DC01 Cold-Rolled Galvanized Coil Is
DC01 cold-rolled galvanized coil is a low-carbon steel coil whose substrate is produced to EN 10130 and then given a hot-dip zinc coating to EN 10346, where it appears as DC01+Z. The cold-rolling route delivers accurate thickness, a smooth surface and consistent flatness, while the zinc layer supplies the corrosion protection that bare cold-rolled steel lacks. This combination is why the product dominates automotive, appliance, construction and general sheet metal work.
Coils are shipped in a range of thicknesses, normally 0.3 mm to 3.0 mm, with widths of 600 mm to 1500 mm, inner diameters of 508 mm or 610 mm and coil weights from about 3 t to 8 t. The product can also be delivered as slit strip, cut-to-length sheet or formed profiles.
Base Material and Chemical Composition
The DC01 substrate is a killed, low-carbon aluminium-bearing steel with tightly controlled residuals, which keeps it formable after cold reduction and annealing.
| Element | Limit | Effect |
|---|---|---|
| Carbon, C | 0.12% maximum | higher carbon raises strength and reduces ductility |
| Manganese, Mn | 0.60% maximum | solid-solution strengthening |
| Phosphorus, P | 0.045% maximum | embrittlement risk if excessive |
| Sulphur, S | 0.045% maximum | inclusion control |
| Aluminium, Al | 0.020% minimum | killing and resistance to ageing |
Low carbon and low residuals keep the yield point under control, so the coil flattens without stretcher strain marks after skin passing and takes paint without flaking.
Mechanical and Coating Properties
| Item | Typical value | Reference |
|---|---|---|
| Tensile strength Rm | 270-410 MPa | EN 10130 |
| Yield strength Re | 140-300 MPa | EN 10130 |
| Elongation A80 | 28% minimum below 0.7 mm, 30% minimum from 0.7 mm | EN 10130 |
| Zinc coating mass | Z60, Z80, Z120, Z275 | EN 10346 |
| Coating type | pure zinc GI or electrogalvanized EG | EN 10346 |
| Surface treatment | chromate-free passivation, oiling or anti-finger print | order requirement |
Where a customer needs a matt grey surface for welding or painting, the same substrate can be supplied as DC01+ZF with a zinc-iron alloy layer instead of free zinc.
How the Coil Is Made
Pickling removes mill scale from the hot-rolled precursor coil and gives a clean surface for rolling.
Cold rolling reduces the strip to final gauge, typically by 60% to 80%, which raises strength and closes the surface.
Batch or continuous annealing softens the work-hardened strip and restores elongation.
Skin passing of about 0.5% to 1.5% flattens the coil, removes the yield point elongation and sets the surface roughness for painting.
Hot-dip galvanizing passes the strip through a molten zinc bath after fluxing, and the coating mass is set by gas wiping.
Tension levelling, chromate-free passivation, oiling and slitting finish the coil for shipment.
Typical Applications
Automotive: body panels, interior trim carriers, brackets and structural reinforcements.
Home appliances: refrigerator housings, air conditioner panels, washing machine shells.
Construction: light steel keels, ventilation ducts, ceiling grids and cable trays.
Other uses: office furniture, electronic equipment housings, shelving and general stamping.
DC01 Compared with DC04, DC06 and DX51D
DC01 is a general stamping grade, while DC04 and DC06 are deep-drawing grades with progressively higher elongation for complex formed parts such as sink bowls or car panels. DX51D belongs to EN 10346 as the basic coating grade for galvanized structural and general sheet; a galvanized DC01 and a DX51D+Z are often interchangeable in simple bending work, but the DX51D route is optimized for the coating line while DC01 is optimized for forming after coating. When a drawing operation is involved, DC01 or its deep-drawing relatives are the safer specification; when the part is mostly flat with light bends, DX51D+Z usually gives the better price.
Purchasing Checklist
State thickness, width and coil weight, plus the allowed thickness tolerance.
State the coating mass and coating type rather than the words galvanized alone.
State the surface treatment, for example passivated, oiled or anti-finger print.
State the mechanical certificate requirement, including C, Mn, S, P limits and tensile results.
Confirm mechanical property level and handle damage-free packaging for transport.
Frequently Asked Questions
Q: What is the difference between DC01 and DX51D?
DC01 is an EN 10130 cold-rolled forming grade used with or without coating; DX51D is the basic EN 10346 hot-dip coating grade. Galvanized DC01 is written DC01+Z and behaves similarly to DX51D+Z in bending work.
Q: Is DC01 galvanized coil magnetic?
Yes. The substrate is ferritic low-carbon steel, so the finished coil is strongly magnetic and suitable for magnetic conveying and clamping.
Q: What does Z80 mean?
Z80 states that the two coated surfaces carry a total zinc mass of 80 g per square metre, which corresponds to roughly 5.6 micrometres per side.
Q: Can galvanized DC01 be welded?
It can be spot and seam welded, though zinc fumes must be extracted. Zinc-iron coated DC01+ZF welds more easily because it carries less free zinc.
Q: Can the coil be painted directly?
Yes, after cleaning and a suitable pretreatment. Passivated or oiled surfaces should be degreased, and zinc-iron coated material gives the best paint adhesion.
Q: How should the coil be stored?
Keep coils dry, off the floor and under cover. Condensation between wraps causes white rust, so allow air circulation and use the oldest coil first.

