The DC Grade Ladder and Where DC02 Fits
The DC family of cold-rolled low-carbon steels for cold forming is defined in EN 10130, and the current grade list runs DC01, DC03, DC04, DC05, DC06 and DC07. Each step upward buys more formability, more consistent cleanliness and a higher price. DC01 is the general-purpose entry grade for bending and light forming, DC03 covers ordinary drawing work, DC04 handles complex stamped panels, and DC05 and DC06 are stabilised grades reserved for very severe draws and for parts that must not age after forming.
DC02 appears regularly in circulated catalogues and in older drawings, but it is not a current grade of EN 10130. The designation survives from earlier editions of the standard and from parallel national specifications, and it is still quoted by traders who work from historical documents. A buyer who receives an offer for DC02 should establish which standard edition and which property envelope the supplier is actually working to, because the name alone does not define a guaranteed set of mechanical values. In practice, most orders written for DC02 resolve into either DC01 or DC03 once the required forming severity is examined.
Chemical and Mechanical Data for DC01 and DC03
| Item | DC01 | DC03 | DC04 |
|---|---|---|---|
| Carbon, max (%) | 0.12 | 0.10 | 0.08 |
| Manganese, max (%) | 0.60 | 0.45 | 0.40 |
| Tensile strength Rm (MPa) | 270-410 | 270-370 | 270-350 |
| Elongation A80, min (%) | 28 | 34 | 38 |
The pattern in the table is deliberate. Carbon and manganese ceilings fall as the grade number rises, which lowers yield strength and removes the solid-solution hardening that restricts plastic flow. At the same time the tensile window narrows and the elongation floor climbs, so the material becomes softer, more uniform and more predictable in a press. Tensile properties are determined in accordance with ISO 6892-1, and the values apply to the delivered condition after annealing and temper rolling.
The practical effect of the step from DC01 to DC03 is measurable on a press. A part that needs a moderate draw, with a blank that must flow into a cavity rather than simply bend, will often form on DC03 where DC01 splits at the punch corner. The difference is carried by the elongation floor, which rises from 28 % to 34 %, and by the lower carbon and manganese content that reduces the tendency to localised hardening.
What "Prime" Means in Coil and Sheet Trading
Prime material is first-quality product that has passed the producing mill's inspection and is released against the full requirements of the standard, with no reprocessing, patch repair or downgrading. It is normally accompanied by a mill certificate, and for critical work by a 3.1 inspection document under EN 10204 issued against the delivered heat. The alternative descriptions used in the market, such as secondary, downgraded or off-grade material, cover product that has been rejected or relaxed for one or more requirements, typically surface condition, flatness, thickness tolerance or mechanical values.
The commercial difference is not only in the price per tonne. Non-prime coil can carry edge cracks, rust staining, scale residue, wide gauge variation or hardness scatter that produces unpredictable results in a press line. For a fabricator running an automated line at a fixed cycle time, that variation converts directly into stoppages and scrap, and the saving on the invoice is usually spent again in the press shop. Prime status should therefore be stated explicitly on the purchase order together with the inspection document type, rather than being inferred from the words used in an offer.
Surface Condition, Oiling and Storage
Cold-rolled sheet leaves the mill with a controlled surface finish produced by the temper mill, and the roughness range is agreed between mill and buyer because it determines how the material behaves in forming and in painting. A smooth, fine-grained finish suits parts that will be painted directly, while a slightly rougher finish holds drawing lubricant better and can improve performance in a deep draw. The mill applies a thin protective oil that must be compatible with the downstream process, and any drawing compound added in the press shop has to be removable in the cleaning stage that precedes painting or coating.
Storage discipline protects all of this. Coils and sheets should be kept indoors on dry dunnage with the protective wrap intact, because moisture that condenses between wraps leaves rust patterns that survive forming and show through the finished coating. Edge damage and denting from careless handling create defects that cannot be rolled out later, so lifting equipment and stacking practice should be treated as part of the quality system rather than as a logistics detail.
Slitting, Cut-to-Length and Press Feed
Most fabricators buy coil and convert it themselves or through a service centre. Slitting produces strip of a declared width with a cut edge, and it removes the rolled mill edge, which improves width consistency but exposes a sheared edge that is more sensitive to cracking in a tight bend. Cut-to-length lines decoil, level and shear the material into flat sheets, and the quality of the levelling determines residual stress, flatness and camber in the delivered sheet. Laser-cut or punched blanks taken from a level sheet retain the certified mechanical values of the coil, because leveling changes residual stress distribution rather than the tensile properties of the steel.
For high-volume work, coil fed directly into a press line avoids the extra handling of cut sheet and reduces the amount of material scrapped at each sheet end. For lower volumes and for parts that need to be nested across the full width, cut-to-length processing usually produces less waste. The choice should be made on the nesting efficiency of the actual part and on the weight of coil the feed equipment can accept, not on the headline price per tonne of coil alone.
Grade Equivalents for Substitution Checks
When a drawing calls for a Japanese or Chinese grade, the usual cross-references are JIS G3141 SPCC for commercial quality, SPCD for drawing quality and SPCE for deep drawing quality, GB/T 5213 for the Chinese DC01 to DC06 series, and ASTM A1008/A1008M for the CS, FS, DS, DDS and EDDS quality classes. Comparable designations do not carry identical guaranteed values, so any substitution should compare carbon and manganese ceilings, tensile range and elongation floor, and should be supported by the r90 and n90 values where those are specified.
Frequently Asked Questions
Q: Is DC02 still a valid grade?
A: DC02 is not part of the current EN 10130 grade list, which runs DC01, DC03, DC04, DC05, DC06 and DC07. The designation survives from earlier editions and legacy documents, so an offer quoting DC02 should be checked against the property envelope the supplier is actually applying.
Q: What does prime quality mean in practice?
A: Material released against the full requirements of the standard, without repair, reprocessing or relaxation of any property, supported by a mill certificate and by a 3.1 inspection document under EN 10204 where required.
Q: Which grade should be used for a tight bend?
A: DC03 is the usual choice for a tight bend, because its lower carbon and manganese content and its 34 % elongation floor tolerate more surface strain than DC01. Bending across the rolling direction is also easier than bending with it.
Q: Which thicknesses are commonly supplied?
A: Cold-rolled mild steel coils and sheets are normally traded from about 0.4 mm to 3.0 mm, with the widest availability in the range used by general press work and enclosure manufacture.
Q: Do cut sheets have the same properties as the coil they came from?
A: Yes. Coil properties are fixed at the mill, and cut-to-length processing changes residual stress and flatness rather than the tensile values reported on the certificate.
Q: How should mild steel coil be stored?
A: Indoors, on dry dunnage clear of the floor, with the protective wrap intact and with a light film of compatible oil on the surface to prevent condensation rust between wraps.

