Q345 Mechanical Properties: Yield, Tensile and Impact Values Explained

Aug 28, 2025 Leave a message

Q345 is a low-alloy high-strength structural steel defined in the Chinese national standard GB/T 1591 for low-alloy high-strength structural steels. Its mechanical properties, not its name, decide where it can be used in construction, machinery and steel structures. This guide presents the guaranteed values by thickness, explains the quality grades A to E, and shows how to check a mill certificate against the standard.

Designation and Standard Context

The Q in Q345 stands for yield strength, and 345 is the minimum yield strength in MPa for the base thickness range. In GB/T 1591-2018 the designation Q345 has been replaced by Q355 with the same yield requirement, but Q345 remains widely specified in existing projects and older design codes, and mills continue to supply it. When ordering, state the grade and the standard edition, for example Q345B per GB/T 1591, so the certificate matches the contract.

Yield and Tensile Strength by Thickness

Thickness (mm) Yield strength (MPa, min) Tensile strength (MPa) Elongation A (%, min)
<= 16 345 470-630 22
> 16 to 40 335 470-630 21
> 40 to 63 325 470-630 20
> 63 to 80 315 470-630 19
> 80 to 100 305 470-630 18

The values follow GB/T 1591 for Q345 plate in the longitudinal test direction; thicker material carries lower guaranteed yield because the rolling reduction per pass is smaller.

Quality Grades and Impact Energy

Q345 is divided into quality grades by the guaranteed Charpy V-notch impact energy: Q345A has no impact requirement, Q345B guarantees 34 J at 20 degrees Celsius, Q345C at 0 degrees Celsius, Q345D at minus 20 degrees Celsius and Q345E at minus 40 degrees Celsius. The test uses standard Charpy specimens with a 10 x 10 mm cross-section. For outdoor structures in cold regions, select the grade by the lowest service temperature, not by habit.

Chemical Composition Basics

Q345 is a low-alloy steel with deliberate additions of elements such as manganese, silicon, niobium, vanadium and titanium to raise strength without losing weldability. Carbon is kept low, which is why Q345 welds readily with common processes and electrodes designed for high-strength structural steel. The certificate lists the actual ladle analysis, and the limits are defined in GB/T 1591.

Reading a Mill Certificate

Check that the certificate states the grade and standard, the heat number, the plate or coil number, the chemical analysis and the mechanical test values with the specimen orientation. Compare yield, tensile and elongation against the table above for the actual thickness delivered. Confirm that the impact test, if required, was performed at the temperature specified by the grade letter.

Application Guidance

Q345 is used for welded structures, bridges, machinery frames, pressure-bearing supports and components where Q235 sections would be oversized. The strength premium allows thinner sections and lower weight, but stiffness and buckling design may still govern slender members. Confirm that the fabricator's welding procedure and consumables match the grade, and verify the material certificate before fabrication, because mixing Q345 with lower grades in a certified structure creates a traceability failure.

FAQ

Is Q345 the same as Q355?

Q355 in GB/T 1591-2018 carries the same yield requirement as Q345 in earlier editions and is the successor designation. Existing projects often still specify Q345; confirm the edition and grade with the mill.

What does the letter after Q345 mean?

The letter A to E indicates the guaranteed impact energy and test temperature: A has no impact guarantee, B guarantees 34 J at 20 degrees Celsius, C at 0 degrees Celsius, D at minus 20 degrees Celsius and E at minus 40 degrees Celsius.

What elongation does Q345 guarantee?

Minimum elongation is 22 percent for thickness up to 40 mm, stepping down to 21, 20, 19 and 18 percent as thickness increases to 100 mm, tested with the standard proportional gauge length.

Can Q345 be welded without preheat?

For typical plate thicknesses and normal shop conditions, Q345 welds without preheat using suitable electrodes and a qualified procedure. For thick sections or cold conditions, follow the welding procedure specification, which may require preheat.

How do I verify delivered Q345 material?

Check the mill certificate against the grade, thickness and standard, and verify that the mechanical test values meet the table above. For critical structures, arrange third-party sampling and testing per the contract.