The DC Cold-Forming Grade Family under EN 10130
DC01, DC02, DC03, DC04, DC05 and DC06 are the grades of the European cold-rolled low-carbon steel family defined in EN 10130. The letters DC identify steel for cold forming and the number ranks drawability: 01 is the general commercial grade, and each step up the series gives more elongation, a lower yield-to-tensile ratio and better behaviour in deep drawing and stretch forming. The same series replaced the older German designations, so DC01 was St12, DC03 about St13 and DC04 about St14.
SPCC belongs to a different system. It is the most common commercial grade of JIS G3141, the Japanese standard for cold-reduced carbon steel sheet and strip, with carbon limited to 0.15% and manganese to 0.60%. SPCC covers roughly the general forming duty that DC01 covers in Europe, which is why the two are routinely quoted as equivalents.
Grade Comparison Table
| Grade | Forming class | Typical elongation A80 over 0.7 mm | Typical use |
|---|---|---|---|
| DC01 | bending and light forming | about 28% to 30% | ducting, cabinets, guard rails, appliance panels |
| DC02 | drawing | about 34% to 36% | moderate drawn parts, panels with shallow recesses |
| DC03 | deep drawing | about 36% to 38% | deep drawn housings, difficult profiles, beading |
| DC04 | extra deep drawing | about 38% to 40% | sink bowls, complex automotive panels |
| DC05 | special deep drawing | about 40% to 42% | severe draws with heavy wall reduction |
| DC06 | ultra deep drawing, interstitial free | about 42% or higher | the most severe draws, filter shells, complex enclosures |
The elongation bands are indicative and describe the ranking that matters when a grade is selected; the exact minimum for a given gauge is fixed by EN 10130 and confirmed on the mill certificate.
What Changes as the Number Rises
Three things move together along the series. First, chemistry tightens: DC01 allows up to 0.12% carbon and 0.60% manganese, DC03 up to 0.10% carbon and 0.45% manganese, and the highest forming grades are produced with very low carbon, in the case of DC06 with titanium or niobium additions that combine with the remaining carbon so that the steel is effectively interstitial free. Second, the microstructure is optimised: higher grades receive longer annealing and a controlled grain size that raises the plastic strain ratio, so the material resists thinning in the walls of a drawn cup. Third, the ageing behaviour improves, so formed parts do not become brittle in storage and painted panels do not develop stretcher strain marks.
In practice this means DC01 should not be used for a part with a draw depth greater than about half its diameter, while DC04 and above are specified once the draw becomes deep, the radius tight or the blank irregular.
SPCC and Cross-Standard Equivalents
| System | Cold-rolled grade | Zinc-coated grade |
|---|---|---|
| Europe, EN 10130 and EN 10346 | DC01 | DC01+Z |
| China, GB/T 5213 and GB/T 2518 | DC01 | DX51D+Z |
| Japan, JIS G3141 and JIS G3302 | SPCC | SGCC |
| United States, ASTM A1008 and ASTM A653 | CS Type B | CS Type B |
Equivalents map the general duty, not every limit. Aluminium content, residual element control, tolerance class and surface finish differ between systems, so a substitute grade should be confirmed against the drawing requirement rather than the grade name alone.
Coated Versions of the Same Grades
The DC grades are frequently supplied with a hot-dip zinc coating to EN 10346, written DC01+Z for pure zinc or DC01+ZF for zinc-iron alloy, with coating mass from Z60 up to Z275 measured as the total zinc on both surfaces in grams per square metre. Coating does not change the forming classification, but it does change the surface: a zinc-iron coated sheet paints better and welds more easily, while a heavier pure zinc coating gives longer corrosion life and needs more care during severe drawing because the soft layer can pick up on tooling. Where the part will be painted after forming, a light oil film rather than a passivation layer is usually specified so that the drawing lubricant and the paint pretreatment both work properly.
How to Select the Grade
Define the forming operation first: bending and roll forming point to DC01, deep drawing points to DC03 or DC04, and the most severe draws point to DC05 or DC06.
Check the draw ratio and corner radii against the elongation class before fixing the gauge.
Decide whether the part is painted, welded or left bare, because that decides the coating type and surface treatment.
Confirm the standard system and equivalencies in writing, since SPCC, DC01 and CS Type B are not identical in chemistry limits.
Request the mill certificate for the actual heat and coil, with tensile, yield, elongation and coating mass results.
Frequently Asked Questions
Q: What is the difference between DC01 and SPCC?
DC01 is the EN 10130 cold-forming base grade and SPCC is the JIS G3141 commercial cold-reduced grade. Both are general forming materials with similar duties, but limits and tolerances are set by different standards.
Q: Which grade is best for deep drawing?
DC04 covers most deep drawing, DC05 and DC06 are used for the most severe draws, and DC03 is the usual choice for moderately deep parts with difficult profiles.
Q: Is DC06 an interstitial free steel?
Yes. In DC06 the carbon and nitrogen are stabilised by titanium or niobium additions, which leaves the steel effectively free of interstitial atoms and gives it very high elongation and excellent drawability.
Q: Can DC03 be galvanized?
Yes. Any of the DC grades can be hot-dip coated to EN 10346, for example DC03+Z, with the coating mass chosen from the Z60 to Z275 range according to the corrosion duty.
Q: What does the DC letter stand for?
DC stands for steel for cold forming, covering both drawing and coating duties. The number that follows ranks the formability, from 01 for general use up to 06 for ultra deep drawing.
Q: How do I verify the delivered material?
Check the coil label against the certificate for grade, thickness, coating mass and mechanical values, then confirm flatness, surface condition and the absence of white rust on the edges.

