DC05 Steel Sheet and Plate: Thickness Range, Sheet Sizes, Weight Chart and EN 10130 Data

Oct 13, 2026 Leave a message

DC05 is the extra-deep-drawing grade of EN 10130. As sheet it is the same material as DC05 coil, cut to length and levelled, with the same guarantees: yield strength 180 MPa maximum, tensile strength 270-330 MPa, elongation A80 at least 40%, r90 at least 1.9, n90 at least 0.20. This page covers what changes when you buy sheet instead of coil: sizes, sheet weight, flatness, packing, and the thickness question.

DC05 Steel Sheet and Plate

 

1. The Thickness Ceiling

EN 10130 covers cold rolled flat products from 0.35 mm to 3.00 mm. There is no 6 mm DC05 and no 12 mm DC05 - above 3 mm the product is hot rolled, sold under another standard, and the drawing guarantees do not travel with it. If a quotation offers DC05 at 6 mm or more, ask which standard the values are certified to. It usually turns out to be a hot rolled commercial grade sharing a drawing number, not the EN 10130 guarantees.

Practical band for sheet is 0.50-3.00 mm: thinner is hard to level without marking, thicker is no longer this grade.

 

2. Sheet Sizes and Weight

Standard mill widths are 1000, 1219, 1250 and 1500 mm, with 1800 mm from some mills. Length is cut to order; stock lengths are 2000, 2438, 2500 and 3000 mm. Weight comes from one figure: 7.85 kg per millimetre of thickness per square metre.

 

Thickness

kg/m²

kg per 1250 x 2500 sheet

Sheets per tonne

0.7 mm

5.50

17.2

58

0.8 mm

6.28

19.6

51

1.0 mm

7.85

24.5

41

1.2 mm

9.42

29.4

34

1.5 mm

11.78

36.8

27

2.0 mm

15.70

49.1

20

2.5 mm

19.63

61.3

16

3.0 mm

23.55

73.6

14

Multiply by 1.44 for a 1500 x 3000 sheet. Forty sheets of 1.0 mm is about one tonne, normally one pallet.

 

Send Your Requirements

 

3. Flatness Is the Sheet Problem

Coil has shape; sheet has flatness. A length cut from coil keeps part of the coil's curvature: coil set along the length, crossbow across the width, wavy edges where the strip stretched unevenly. Roller levelling removes all three, and a bad shear brings them back. State which you need - levelled for laser cutting, close-tolerance blanking and anything that must lie flat against another part; as-cut is cheaper and fine for deep drawing, where the die flattens the blank anyway.

 

Also fix squareness. The difference between the two diagonals is the usual measure, and it matters if the sheet feeds a nesting program.

 

4. Surface, Protection and Packing

Sheet stacks face to face, so sheet-on-sheet abrasion in transit is a risk coil does not have. Ask for interleaving paper or film between sheets, VCI paper in the pack, and a strapped pallet with edge protection rather than a loose bundle. Corner damage on a stack is scrap, not a cosmetic issue.

Surface quality and finish are ordered as for coil: quality A for forming work, B where one face takes a quality paint or electrolytic coating; finish b bright, g semi-bright, m normal at Ra 0.6-1.9 µm, or r rough. Sheet normally ships oiled; dry supply with film is available.

 

5. Equivalent Grades

Standard

Nearest designation

EN 10130

DC05 (1.0312)

DIN 1623, withdrawn

St15

JIS G 3141

SPCE, SPCF

ASTM A1008

DDS / EDDS

ISO 3574

CR4

IS 513

CR4

GB/T 5213

DC05

GOST 9045

08Yu (08ю)

Commercial matches, not certified substitutions: two grades on the same line can still differ in guaranteed r90 and n90, which is what decides a difficult draw. Where the part is critical, specify the mechanical values on the order.

 

7. FAQ

 

Is DC05 sheet stronger than DC04 sheet?

No, it is softer. Yield strength is a ceiling of 180 MPa against 210 MPa for DC04, and that softness buys the extra draw depth.

Can we laser cut it?

Yes. Levelled sheet sits flat on the bed, and the oil film should be allowed for or removed first.

Does sheet cost more than coil?

Slightly, for the extra handling, levelling and packing. It saves you the decoiler and the leveller.

 

Get a Quote on DC05 Sheet

Send thickness, sheet size, quantity in tonnes or sheets, surface requirement and destination port. GNEE STEEL replies within 24 hours with the sizes we can hold, the certificate we will issue, and a price.