Double Coating and Double Baking Process for Galvanized Coil

Sep 02, 2025 Leave a message

What Double Coating and Double Baking Means

Colour-coated (prepainted) steel coil is made on a continuous coil-coating line. In the single-pass route, primer and topcoat are applied one after the other and both are cured in a single oven, a practice often described as two coats one bake. In the double coating and double baking route, the coil makes two passes through the line: the primer is applied, cured, cooled and rewound, and the topcoat is applied in the second pass and cured again. The galvanized or zinc-aluminium substrate is the same in both cases; what changes is the number of thermal cycles the coating system receives and the degree of conversion achieved in each layer.

Why the Intermediate Bake Matters

Curing is a chemical reaction as well as a drying step. When the primer is fully cross-linked before the topcoat is applied, the primer forms a dense, solvent-free film that anchors the topcoat and blocks the passage of moisture and chloride ions to the zinc interface. In a single-bake process the two layers cure together and the primer may remain partly uncured, which shows up later as intercoat delamination, blistering at cut edges or poor performance in salt spray. The double bake also allows the primer to be formulated with a higher pigment volume concentration and a different resin chemistry from the topcoat, so corrosion inhibitor pigments and adhesion promoters can be used at their optimum loading.

Key Process Parameters

Stage Typical parameter Purpose
Uncoiling and levelling Levelness within 0.5 mm/m Removes coil set and ripples so the coating is uniform
Degreasing Alkaline cleaner, 2 to 5% concentration, 40 to 60 C, 10 to 30 s Removes rolling oil, dust and fingerprints
Rinsing Two to three clean-water stages Prevents cleaner residue from attacking adhesion
Surface conditioning Conversion film up to about 1 um Improves adhesion and adds barrier corrosion resistance
Primer application Roller coater, controlled wet film Establishes adhesion to the zinc surface
Primer bake Oven cure of the primer only Full cross-linking before the topcoat
Topcoat and second bake Colour coat applied and cured in a second pass Colour, gloss and weather resistance

Coaters control the coating thickness by the ratio of the pick-up roller to the applicator roller and by line speed. Both are recorded as part of the line log, because film thickness and cure degree are the two variables that most often explain a rejected coil.

Where the Process Is Used

Double coating and double baking is specified for architectural cladding, roofing and walling that must hold colour and gloss for decades, for appliance and HVAC panels that face repeated cleaning, and for any part exposed to coastal or industrial atmospheres. On zinc-aluminium substrates the same route is used when a textured or metallic finish is required, because the second pass can carry a different topcoat chemistry from the first. Weldable and formable coatings are also produced this way, since a fully cured primer tolerates the bending and roll-forming that follows without cracking at the bend radius.

Quality Checks on a Finished Coil

The routine checks are coating mass per unit area on each side, dry film thickness, adhesion by cross-hatch or T-bend, impact resistance, gloss and colour difference against a master panel, and salt-spray performance for the specified exposure hours. T-bend testing is the quickest way to detect an under-cured primer, because a coating that delaminates at a 2T bend is almost always under-cured or under-conditioned at the substrate interface. Coils should be stored under cover at moderate humidity, and cut edges should be protected in severe environments, since the coating system cannot protect an exposed edge as effectively as the zinc beneath it.

Frequently Asked Questions

Q: Is double baking always better than a single bake?
A: Not automatically. It gives better intercoat adhesion and a more complete cure, but it adds a pass, more energy and a higher unit cost, so it is used where the durability or the film build justifies it.

Q: Can double coating and double baking be applied to any substrate?
A: It is most common on hot-dip galvanized and zinc-aluminium coated coil, but it can be applied to cold-rolled and electro-galvanized substrates provided the pre-treatment stage is matched to that surface.

Q: Does the process change the corrosion performance of the zinc coating?
A: The zinc coating itself is unchanged. The gain comes from the barrier and adhesion quality of the paint system, which reduces the rate at which the zinc is consumed.

Q: What thickness can be achieved?
A: Film build depends on the roller settings and the number of passes. Two fully cured passes give a thicker, more uniform system than two wet layers cured together, which is why the route is chosen for exterior cladding.

Q: How is an under-cured primer detected?
A: By T-bend and cross-hatch adhesion tests, and by solvent rub resistance. Poor results at a 2T bend with otherwise good thickness readings point to incomplete cure.