Why These Grade Codes Appear Together in Export Orders
Orders from markets such as Djibouti and Ethiopia frequently list several grade codes together - DX51D, DC01, SPCC, SGCC, GI, GL, PPGI and PPGL - because a single roofing or cladding project uses cold rolled substrate, galvanized and aluminium-zinc coated coils, and prepainted coils at the same time. Each code names a different stage of the same product family: the cold rolled base steel, the coating type, and the paint system. Understanding the hierarchy helps buyers check that the ordered grade matches the required formability and corrosion life.
DX51D: The Bending and Profiling Grade of EN 10346
Grade DX51D is defined in EN 10346, the European standard for continuously hot-dip coated steel flat products. It is a bending and profiling grade, suitable for simple craft forming work and for the production of simple profile shapes such as trapezoidal sheets, corrugated sheets, purlins and light framing. The D stands for the steel for cold forming, X marks the hot-dip coated product, 51 is the grade serial number within the family, and the final letter D denotes a metallic coating that is suitable for subsequent forming.
Thickness and width range
DX51D is commonly available in thicknesses of 0.45-3.00 mm and widths up to 1520 mm. The relatively wide availability of thin gauges makes it the standard choice for roll-formed cladding profiles, where the coating must survive bending without flaking.
DX51D Equivalence and the JIS Counterpart SGCC
DX51D is frequently described as equivalent to SGCC, the hot-dip galvanized steel sheet of JIS G3302. Both are low-carbon steel based commercial-quality galvanized products intended for general forming. Strictly speaking the two grade systems are not interchangeable specification by specification - EN 10346 and JIS G3302 define different property tables - but for typical bending and profiling work they occupy the same position in their respective systems. When an order specifies one and receives the other, the practical performance for simple profiles is comparable.
DX51D uses low-carbon steel as the base material and the digit 51 indicates the bending and forming grade in the EN coated-steel family. For more demanding forming, the family steps up through DX52D, DX53D and DX54D with progressively higher formability.
DX53D: The Deep-Forming Step and Its Material Numbers
DX53D is a higher-formability grade of the same family, suited to deep drawing and complex profiling. Its designation has changed across revisions of the standard: under EN 10346:2009, DX53D corresponds to the material number 1.0355, while under EN 10346:2015 the equivalent designation is 1.0952. When a drawing or certificate quotes a steel number, confirming the standard year of reference prevents confusion between the two designations.
DC01 and SPCC: The Cold Rolled Substrates
DC01 is a cold rolled low-carbon steel for cold forming defined in EN 10130, suitable for simple bending and shallow forming. SPCC is the cold rolled commercial grade defined in JIS G3141, widely used for panels and general stampings. Both grades serve as substrates for the coated product family: after pickling, cold rolling and annealing, the strip is coated on a continuous line to become GI, GL, PPGI or PPGL. For forming-heavy applications the substrate grade must be chosen with the final profile in mind, because the coating cannot compensate for insufficient substrate formability.
GI, GL, PPGI and PPGL for Tropical and Coastal Climates
GI (galvanized iron) carries a pure zinc coating; GL carries a zinc-aluminium alloy coating with roughly 55% aluminium. PPGI and PPGL are the prepainted versions, where the coated strip receives a paint system - polyester, silicone-modified polyester or PVDF - in a coil-coating line. In the hot, high-solar-load climates of the Horn of Africa, coated coils are chosen for heat reflectivity and corrosion resistance; near the coast, heavier zinc coatings and higher-performance paint systems are preferred because of salt spray.
| Grade / product | Standard | Role | Typical thickness | Typical use |
|---|---|---|---|---|
| DX51D+Z | EN 10346 | Bending/profiling galvanized | 0.45-3.00 mm | Corrugated sheets, trapezoidal profiles |
| DX53D+Z | EN 10346 | Deep-forming galvanized | 0.45-3.00 mm | Complex profiles, drawn parts |
| SGCC | JIS G3302 | Hot-dip galvanized sheet | 0.25-3.2 mm typical | Roofing, structures, general forming |
| DC01 | EN 10130 | Cold rolled substrate | 0.3-3.0 mm typical | Bending, shallow stamping |
| SPCC | JIS G3141 | Cold rolled commercial | 0.3-3.2 mm typical | Panels, enclosures, general parts |
| PPGI / PPGL | EN 10169 / coating spec | Prepainted coated coil | 0.20-2.0 mm typical | Roofing, wall cladding, appliances |
Frequently Asked Questions
Q1. What is DX51D material grade?
DX51D is a bending and profiling grade of continuously hot-dip coated steel defined in EN 10346. It is suitable for simple craft forming work and the production of simple profile shapes such as corrugated and trapezoidal sheets.
Q2. What is the thickness range of DX51D?
DX51D is available in thicknesses of 0.45-3.00 mm and widths up to 1520 mm. Within this range the coating must survive roll forming without flaking.
Q3. What is DX51D equivalent to?
DX51D is commonly compared with SGCC of JIS G3302. Both are low-carbon, commercial-quality galvanized products for general forming. The EN and JIS systems define different property tables, but for simple bending and profiling the two grades play the same role.
Q4. What is DX53D steel equivalent to?
Under EN 10346:2009, DX53D corresponds to material number 1.0355; under EN 10346:2015 the equivalent designation is 1.0952. DX53D offers higher formability than DX51D for deep drawing and complex profiles.
Q5. What is the difference between PPGI and PPGL?
PPGI is prepainted galvanized iron with a pure zinc coating; PPGL is prepainted aluminium-zinc with a zinc-aluminium coating of about 55% aluminium. PPGL generally offers longer corrosion life and better heat reflectivity in hot climates.
Q6. Which grade should I choose for roofing profiles in a coastal export market?
For simple roofing profiles, DX51D+Z or SGCC with a heavy zinc coating is the standard choice; near the coast, select a higher coating weight and, if colour is required, a PPGL coil with a polyester or PVDF system to resist salt spray.

