What a Galvanized Steel Coil Is
A galvanized steel coil is a continuous strip of thin steel that has passed through a molten zinc bath so that a metallurgically bonded zinc layer forms on both surfaces. The coil is supplied in the coated, levelled and usually skin-passed condition, ready for slitting, profiling, blanking or roll forming. The coating protects the substrate both as a barrier and, where the surface is scratched or sheared, as a sacrificial anode.
Coils are grouped into two families. Hot-rolled galvanized coil starts from pickled hot-rolled strip and is used where thickness and cost matter more than surface perfection. Cold-rolled galvanized coil starts from cold-reduced and annealed strip and gives the flatness, surface quality and formability required for exposed parts, appliance panels, automotive components and steel silos.
The Manufacturing Route, Step by Step
Pickling and cold reduction: hot-rolled strip is pickled to remove mill scale, then cold rolled to the ordered thickness where a cold-rolled substrate is required.
Cleaning and annealing: the strip is degreased and annealed to restore ductility and to present a chemically clean surface to the zinc.
Hot-dip galvanizing: the strip passes through a molten zinc bath at approximately 450 to 460 degrees Celsius, where the coating forms. Aluminium in the bath controls the iron-zinc reaction and improves adhesion.
Coating mass control: an air knife wipes excess zinc from both faces immediately above the bath; the knife pressure and line speed set the final coating mass to the ordered class, from light coatings up to the heaviest building grades.
Cooling and spangle control: the cooling profile and the addition of a grain refiner determine whether the surface shows a pronounced regular spangle, a minimum spangle, a zero spangle or a large spangle finish.
Skin pass and tension levelling: a light rolling pass improves flatness, surface texture and forming behaviour, and suppresses stretcher strain during pressing.
Surface treatment and packing: a chromate or chrome-free passivation film and a thin oil film prevent white rust in transit; the coil is then slit to width, weighed and packed for sea transport.
Grade Range: DX51D, DX52D and DX53D
The DX series is the European continuously hot-dip coated family, now specified under EN 10346; the earlier EN 10327 and DIN 17162 designations have been withdrawn. SGCC and the SGCD grades belong to the Japanese system under JIS G3302, while ASTM A653M covers the equivalent US commercial and structural classes. The three DX grades are distinguished by forming capability rather than by coating.
| Grade | System | Forming class | Typical use |
|---|---|---|---|
| DX51D | EN 10346 | Bending and forming, lowest ductility of the DX series | Construction profiles, general fabrication, ducting |
| DX52D | EN 10346 | Drawing quality, intermediate ductility | Appliance parts, housings, simple drawn components |
| DX53D | EN 10346 | Deep drawing quality, highest ductility | Deep drawn panels and complex formed parts |
| DC51D+Z | EN 10346 | Bending and forming, cold-reduced substrate | General coated sheet |
| SGCC | JIS G3302 | Commercial quality | Building, appliances, containers |
| ASTM A653 class | ASTM A653M | Commercial or forming steel classes | US specification projects |
Because the DX grades are defined primarily for formability, they are not intended for structural load-bearing duty. Where a coated product must carry design loads, a structural grade with declared minimum yield strength is selected instead.
Z120 and the Full Coating Range
Coating designations state the total zinc mass on both surfaces, expressed in grams per square metre. Z120 therefore means 120 grams per square metre in total, or about 60 grams per square metre on each face; converting that to thickness gives roughly 8 to 9 micrometres per side, which places it in the middle of the galvanized range and suits general building, appliance and container applications with moderate indoor or sheltered exposure.
| Designation | Total coating mass | Approximate thickness per side | Typical environment |
|---|---|---|---|
| Z100 | 100 g/m2 | About 7 micrometres | Indoor, dry interior parts |
| Z120 | 120 g/m2 | About 8 to 9 micrometres | Sheltered building and appliance parts |
| Z180 | 180 g/m2 | About 13 micrometres | Exposed industrial and rural building |
| Z275 | 275 g/m2 | About 19 to 20 micrometres | Heavy building and structural profiles |
| AZ150 | 150 g/m2 of aluminium-zinc coating | About 20 micrometres | Roofing and cladding in aggressive atmospheres |
The AZ designation belongs to the 55 percent aluminium, 43.4 percent zinc and 1.6 percent silicon alloy coating, which trades a small loss of sacrificial edge protection for substantially better heat reflectivity and long-term performance in marine and industrial environments. Coating mass is verified by stripping and weighing samples from the coil ends or by non-destructive magnetic measurement, and the ordered class should always be stated as a total mass so that both faces are covered.
Dimensional and Supply Specification
| Parameter | Range or value |
|---|---|
| Standard | JIS G3302, ASTM A653M, EN 10346 |
| Grade | SGCC, DC51D, DX51D, DX52D, SGSS, SGCD1, SGCD2, SGCD3 |
| Thickness | 0.12 to 3.5 mm |
| Width | 600 to 1250 mm, with common widths of 914, 1000, 1200, 1219, 1220 and 1250 mm |
| Spangle | Regular, minimum, zero and large spangle |
| Zinc coating | 30 to 275 g/m2 total |
| Hardness | Soft, up to HRB 60; medium, HRB 60 to 85; full hard, HRB 85 to 95 |
| Coil inner diameter | 508 mm or 610 mm |
| Coil weight | 4 to 6 tonnes |
| Packing | Waterproof paper, steel strapping and wooden pallet suitable for sea transport |
| Delivery | 7 to 15 days after receipt of advance payment |
| Order size | 25 tonnes or one container as a regular order; smaller quantities on request |
| Monthly capacity | 20 000 tonnes |
Loading is planned against container internal dimensions: a 20 foot general purpose container takes about 24 to 26 cubic metres and a maximum coil width of 5.8 m, while 40 foot general purpose and high cube containers take the same width up to 11.8 m with about 54 and 68 cubic metres respectively. Orders above roughly 100 tonnes can be shipped in bulk. Coils are banded inside the container and blocked against movement, and wooden or iron pallets with separating partitions are used where moisture protection is critical.
Frequently Asked Questions
Q: What is the difference between DX51D, DX52D and DX53D?
All three are continuously hot-dip coated grades with a low-carbon substrate, but they are ranked by formability. DX51D is intended for bending and profiling, DX52D for drawing quality work, and DX53D for deep drawing. As formability increases, the material is easier to shape without cracking and the base steel is softer.
Q: How much zinc is in a Z120 coating?
Z120 designates 120 grams per square metre of zinc in total across both surfaces, which is about 60 grams per square metre on each face, or roughly 8 to 9 micrometres of coating per side.
Q: When should I specify Z275 instead of Z120?
Choose the heavier class when the finished part will be exposed to weather, industrial pollution or coastal air without further painting, or when the profile is difficult to repaint after installation. Z120 is sufficient for sheltered building elements, appliance housings and interior components.
Q: What does spangle mean and does it affect performance?
Spangle is the visible crystalline zinc grain pattern formed as the coating solidifies. Regular spangle is the traditional appearance, zero spangle is smoother and preferred for painting or high-quality appearance, and minimum or large spangle are ordered to suit the customer's finish requirement. The choice affects appearance and painting behaviour more than corrosion performance at equal coating mass.
Q: Can galvanized steel coil be used for structural parts?
Only if a structural grade with a declared minimum yield strength is specified. The DX series and SGCC commercial quality grades are defined for forming and general fabrication, not for load-bearing design, and structural classes such as the ASTM A653 structural grades should be ordered instead.
Q: What does HRB 60 to 95 hardness tell me about a coil?
The Rockwell hardness band indicates the temper of the strip. Soft coils up to approximately HRB 60 form easily and suit deep drawn or profiled parts, medium hardness coils around HRB 60 to 85 suit general forming, and full hard coils in the HRB 85 to 95 range are used where stiffness and flatness matter more than ductility.

