GI Hot Dipped Galvanized Steel SGCC SGCH DX51D DX52D DX53D

Sep 30, 2025 Leave a message

Three Grade Systems Behind One Galvanized Coil

A hot-dip galvanized coil enquiry usually names grades from two or three different standards at once. SGCC and SGCH come from JIS G3302; DX51D, DX52D and DX53D come from EN 10346; and CS, FS, DDS, EDDS and the SS structural grades come from ASTM A653/A653M. They describe the same product family, a continuously hot-dip zinc coated steel flat product, but the property requirements and the designation logic differ, so a purchase order must name the standard as well as the grade.

The EN system embeds formability in the number: the D denotes a flat product for cold forming, X denotes a cold-reduced substrate, and the two digits describe the forming level, so DX51D is a commercial grade and DX53D is a deep drawing grade. The JIS system uses letters instead: SGCC is commercial quality, SGCD is drawing quality and SGCH is a higher strength commercial grade. The ASTM system separates product type from property, with commercial steel, forming steel, drawing and extra deep drawing steel alongside structural grades named by minimum yield strength in ksi.

Mechanical Property Comparison

Grade Minimum yield strength Tensile strength Forming role
DX51D+Z Not specified as a minimum 270-500 MPa Commercial forming, shallow profiles
DX52D+Z Not specified as a minimum 270-420 MPa Forming and moderate drawing
DX53D+Z Not specified as a minimum 270-380 MPa Deep drawing
DX54D+Z Not specified as a minimum 260-350 MPa Extra deep drawing
S250GD+Z 250 MPa 330 MPa minimum Structural, light load
S350GD+Z 350 MPa 420 MPa minimum Structural, general load
S550GD+Z 550 MPa 560 MPa minimum Structural, high strength

The A80 elongation values follow the same progression under EN 10346: at least 22% for DX51D+Z, 26% for DX52D+Z, 30% for DX53D+Z and 36% for DX54D+Z. Reading the table the other way round is the practical way to select a grade: identify the tightest bend radius and the deepest draw in the shop drawing, then choose the lowest forming grade that covers it, because formability is bought with tensile strength and downgrading a structural part to gain formability is a design error.

Coating Mass and Surface Finish

Under ASTM A653/A653M the coating designation is a G number expressed in ounces per square foot over both faces, so G60 equals 0.60 oz/ft2 and G90 equals 0.90 oz/ft2, which is approximately 275 g/m2. Under EN 10346 the same quantity is stated directly in grams per square metre over both faces, for example Z100 or Z275, and one micrometre of pure zinc corresponds to about 7.14 g/m2, so Z275 is roughly 19 micrometres per side. The JIS G3302 symbols work on a number times ten logic, so Z27 is 270 g/m2 over both faces.

Surface finish is specified separately from coating mass. Normal spangle is the as-solidified crystal pattern, minimised spangle is produced by controlling the zinc bath chemistry and cooling, and skin passed finish is lightly rolled to flatten the spangle for painting. Skin passing also raises the yield point and reduces stretcher strain, so a skin passed coil that is subsequently deep drawn may require a re-anneal or a temper rolled alternative.

Processing: Cutting, Joining and Painting

Shearing and slitting are preferred over abrasive or thermal cutting, because heat destroys the coating locally and leaves an uncoated edge. Where welding is required, the coating must be removed from the weld zone and restored afterwards with a zinc-rich repair material, since zinc vaporises at steel welding temperatures and produces porosity. Forming forces increase slightly with coating mass, and lubricants must be chosen so that zinc debris does not accumulate on the dies. Painting requires a conversion coating or a suitable pretreatment; painting directly over a freshly galvanized surface without passivation usually fails adhesion tests within a short time.

Applications and Field Performance

The main outlets are roof and wall sheet, home appliance panels, office partitions, automotive underbody and chassis parts, and the painted coil substrate. Roofing and cladding take the largest volume, and their service life is set by the coating mass plus the local atmosphere. In combined salt and sulphur environments, a 275 g/m2 coating will outlast a 100 g/m2 coating by a wide margin, and the corrosion rate at an unprotected cut edge is several times the rate on the flat surface, which is why edge treatment is specified on long-life roofs.

Frequently Asked Questions

Q: Is DX51D the same as SGCC?
A: They are close but not identical. Both are commercial quality hot-dip galvanized cold-reduced products from different standards, EN 10346 and JIS G3302. Substituting one for the other requires a comparison of the guaranteed mechanical properties and coating designation, not just the grade name.

Q: What does the plus sign in DX51D+Z mean?
A: The suffix identifies the coating: +Z is pure zinc from a hot-dip bath, and +AZ is the aluminium-zinc coating containing about 55% aluminium, 43.4% zinc and 1.6% silicon. The base metal grade letters are identical, so the coating must always be stated.

Q: Why is the yield strength not specified for DX52D?
A: The DX drawing grades are defined by tensile range and elongation rather than a minimum yield value, because the forming behaviour and strain ageing characteristics matter more for drawing than a yield floor. Where a structural minimum is required, the S series grades such as S250GD or S350GD are the correct choice.

Q: How much zinc is needed on a roof sheet?
A: For a normal inland industrial atmosphere, 180 to 275 g/m2 total is common practice. Coastal and heavily polluted sites justify a higher mass or an aluminium-zinc coating, together with cut-edge treatment and compatible fasteners.

Q: Does galvanized coil need a passivation treatment?
A: Yes for storage and transport, where it prevents white rust between coils. Chromate-free passivation is now the usual specification, and the treatment must be compatible with the paint system if the coil will be coil coated later.

Q: What is spangle and does it matter?
A: Spangle is the visible zinc crystal pattern formed as the coating solidifies. It is a cosmetic characteristic, but larger spangle generally means a slightly rougher surface that can print through thin paint films, which is why minimised spangle or skin passed finish is specified for painted applications.