What a Color Coated Steel Sheet Is
A color coated sheet, also called a pre-painted or coil-coated sheet, is a steel substrate that has been cleaned, chemically pretreated and then given one or more layers of liquid paint by roller coating before the coil is cut into sheet. The substrate is usually cold-rolled steel or a metallic-coated steel such as hot-dip galvanized or 55% aluminium-zinc coated coil. After the paint is baked and cooled, the coil is either sold as a coated coil or cut and profiled into roofing sheets, wall panels and appliance parts. The paint is applied to a moving strip at line speeds of tens of metres per minute, which is why coil coating gives a more uniform film than piece-by-piece spraying.
Substrates Used for Pre-Painted Coils
Cold-rolled substrate: commercial-quality cold-reduced sheet such as SPCC to JIS G3141 or DC01 to EN 10130. It is used for indoor panels where barrier protection from the paint alone is sufficient.
Hot-dip zinc coated substrate: SGCC to JIS G3302 or DX51D+Z to EN 10346. The zinc layer protects sheared edges, so this is the usual substrate for outdoor roofs and cladding.
Aluminium-zinc coated substrate: SGLCC to JIS G3321 or DX51D+AZ to EN 10346, chosen for long-life architectural work and heat-reflective roofing.
Substrate choice drives the corrosion result far more than paint colour does. A polyester film on cold-rolled steel will not survive an outdoor roof, while the same film on a zinc coated substrate performs well for years because the metallic coating protects the cut edges where paint coverage stops.
Paint Systems and Typical Dry Film Thickness
Coil coating is a two-layer system by default: a primer for adhesion and corrosion inhibition, and a topcoat that carries the colour and gloss. A back coat is applied to the reverse face to prevent marking when coils are stacked and to protect the underside in service.
| Paint system | Typical topcoat DFT | Typical primer DFT | Common use |
|---|---|---|---|
| Polyester (PE) | 18 to 25 µm | 5 to 8 µm | General building panels, indoor parts |
| Silicon-modified polyester (SMP) | 20 to 25 µm | 5 to 8 µm | Roofing with better chalk resistance |
| Polyurethane (PU) | 20 to 25 µm | 5 to 8 µm | Exterior cladding needing colour stability |
| PVDF fluoropolymer | 23 to 27 µm | 7 to 9 µm | High-end architectural facades |
| Back coat | 5 to 12 µm | not applicable | Reverse face, stacking protection |
Dry film thickness is measured after curing. The thickness of the zinc or alloy coating beneath the paint is specified separately, so an order should quote both: for example SGCC with a Z27 equivalent coating and a 20 µm polyester topcoat. Relevant product standards include ASTM A755 for prepainted metallic-coated steel sheet, EN 10169 for continuously organic coated flat products, and JIS G3312 for prepainted hot-dip zinc coated sheet.
How the Coil Coating Line Works
The process is continuous and unbroken from uncoiler to recoiler. In sequence, the strip is uncoiled and stitched to the previous coil, accumulates in an entry looper so that the line can run without stopping, is degreased in an alkaline cleaner, rinsed, and given a chemical conversion coating, which today is normally chrome-free. A primer is applied by roller coater and cured in an oven to a peak metal temperature that suits the paint chemistry, typically in the range of 200 °C to 240 °C. The topcoat is then applied by roller coater, cured at a similar peak metal temperature, cooled through a water quench and air knives, accumulated in an exit looper, and rewound with interleaving paper or film where the finish is sensitive. Film thickness is controlled by the roller pattern and the line speed, and the peak metal temperature is the variable that most affects adhesion and flexibility.
Applications That Suit Color Coated Sheet
Building and construction: roofs and roof structures, wall cladding, sandwich panels, rolling shutter doors, kiosks and shelters, louvres, ventilation ducts and rainwater goods.
Appliances: refrigerator and freezer cabinets, air-conditioner housings, washing machine casings, cooker and heater bodies, electronic appliance enclosures.
Transport and general industry: vehicle roof and side panels, trailer linings, ship partitions, hoardings and signage panels, furniture and shelving.
Construction remains the largest outlet, especially factory buildings with steel structures, composite panel buildings and profiled tile production.
What to Check Before Accepting a Coated Coil
Adhesion: cross-hatch or T-bend test after the panel has been formed, not only before.
Hardness and impact: pencil hardness and reverse impact on the delivered film.
Colour: measured colour difference against the approved standard under the same illuminant, including batch-to-batch consistency.
Solvent resistance: MEK double rub as a simple cure check.
Gloss: 60 degree gloss reading against the specified value.
Corrosion: salt spray or cyclic test on the specified substrate, with sheared edges left exposed.
Storage also matters: coated coils should be kept dry, off the floor, away from condensation and rotated so that older stock is used first, because paint films and interleaving can bond if a coil is stored warm and damp for long periods.
Frequently Asked Questions
Q: What is a color coated sheet made of?
A metallic substrate, usually cold-rolled or hot-dip galvanized steel, that has been pretreated and given a primer and a coloured topcoat by roller coating, then baked and cooled.
Q: What is the difference between PPGI and PPGL?
PPGI is pre-painted galvanized iron, meaning the substrate carries a zinc coating as in SGCC or DX51D+Z. PPGL is pre-painted galvalume, meaning the substrate carries a 55% aluminium-zinc alloy coating as in SGLCC or DX51D+AZ. The paint system can be identical; the difference is the corrosion layer underneath it.
Q: Which paint system should be used outdoors?
Polyester is the economical choice for general building panels, silicon-modified polyester adds chalk resistance on roofs, polyurethane improves colour stability, and PVDF is used where a facade must hold colour and gloss for a long service life.
Q: Why is a back coat needed?
The reverse face is visible on many profiles and is exposed to condensation. A back coat of about 5 to 12 µm protects the metallic coating, prevents marking when coils are stacked, and keeps the underside from rusting early.
Q: Is the paint applied before or after profiling?
Before. Coil coating paints a flat strip, so the film is uniform in thickness. Profiling after coating can crack the film at tight bends, which is why flexibility and T-bend results matter when a heavy profile is planned.
Q: How should color coated sheets be cut and formed?
Use tooling that does not chip the film, avoid dragging cut edges across the finish, and seal or cover sheared edges in corrosive environments because the edge is where the substrate is exposed.

