High Zinc Coating Galvanized Seamless Steel Round Tube for Fluid and Structural Use

Nov 05, 2025 Leave a message

High zinc coating galvanized steel round tube is a seamless hollow section that carries a hot-dip zinc layer over its full surface, inside and outside. Because the tube is pierced and rolled without a longitudinal weld, the wall is uniform and free of a heat-affected seam, so it resists internal pressure, bending and torsion more predictably than a welded pipe of equal weight. The zinc layer adds barrier protection together with sacrificial action at cut ends, threaded joints and accidental scratches. That combination is why galvanized seamless tube is specified for fluid transfer lines, mechanical components and exposed structural frames.

Why a Seamless Round Tube Is Galvanized

A welded pipe carries a seam that has to be normalized, inspected and tested; a seamless tube does not. Where the duty involves cyclic pressure, elevated temperature or a load-bearing frame, the seamless route removes a known weak point and permits a higher design stress. Galvanizing is then applied to control atmospheric corrosion. Ordinary indoor service accepts a light commercial coating, while outdoor storage, buried service, humid interiors or coastal air call for a heavier coating mass agreed between buyer and supplier. Coating mass, rather than nominal thickness, is the acceptance quantity normally used for galvanized tube and is stated in grams per square metre over both surfaces.

Standard Range Available for Galvanized Seamless Tube

Seamless tube is ordered against product standards that fix chemistry, heat treatment and testing. The grades below are the ones commonly supplied with a galvanized finish; coating is applied after the tube has been tested, straightened and cut to length.

Executive standard Grade / material Typical service
ASTM A53 A, B Black and hot-dipped zinc-coated steel pipe, welded and seamless
ASTM A106 A, B, C Seamless carbon steel for high-temperature service
ASTM A179 Low-carbon steel Seamless cold-drawn heat exchanger and condenser tubes
ASTM A192 Low-carbon steel Seamless carbon steel boiler tubes for high pressure
ASTM A210 A-1, C Seamless medium-carbon boiler and superheater tubes
ASTM A213 T5, T11, T12, T22, TP347H Seamless ferritic and austenitic alloy boiler, superheater and heat exchanger tubes
ASTM A312 TP304/304L, TP316/316L Seamless stainless steel pipe for corrosive service
ASTM A333 Grade 6 Seamless and welded steel pipe for low-temperature service
ASTM A335 P9, P11, P22 Seamless ferritic alloy steel pipe for high-temperature service
ASTM A519 4130, 4140 Seamless carbon and alloy steel mechanical tubing
ASTM A789 Duplex stainless grades Seamless ferritic / austenitic stainless tubing for general service

API Grades for Line Pipe and Oil Country Tubular Goods

Standard Grade / material Product
API Spec 5CT H40, J55, K55, N80, L80, C90, C95, T95, P110, Q125 Casing and tubing
API Spec 5L PSL1 / PSL2 A, B, X42, X46, X52, X56, X60, X65, X70, X80 Line pipe

The tables below give the maximum content of carbon, manganese, phosphorus and sulphur together with the minimum tensile and yield strength for the API 5L grades most often supplied as galvanized round tube.

API 5L PSL1 C max % Mn max % P max % S max % Tensile min MPa Yield min MPa
A 0.22 0.90 0.030 0.030 331 207
B 0.28 1.20 0.030 0.030 414 241
X42 0.28 1.30 0.030 0.030 414 290
X46 0.28 1.40 0.030 0.030 434 317
X52 0.28 1.40 0.030 0.030 455 359
X56 0.28 1.40 0.030 0.030 490 386
X60 0.28 1.40 0.030 0.030 517 414
X65 0.28 1.40 0.030 0.030 531 448
X70 0.28 1.40 0.030 0.030 565 483
API 5L PSL2 C max % Mn max % P max % S max % Tensile min MPa Yield min MPa
B 0.24 1.20 0.025 0.015 414 241
X42 0.24 1.30 0.025 0.015 414 290
X46 0.24 1.40 0.025 0.015 434 317
X52 0.24 1.40 0.025 0.015 455 359
X56 0.24 1.40 0.025 0.015 490 386
X60 0.24 1.40 0.025 0.015 517 414
X65 0.24 1.40 0.025 0.015 531 448
X70 0.24 1.40 0.025 0.015 565 483
X80 0.24 1.40 0.025 0.015 621 552

DIN and EN Grades for Seamless Tube

Executive standard Grade / material Product
DIN 17175 / EN 10216-2 St35.8, St45.8, 13CrMo44 to DIN 17175; P235GH, P265GH, 13CrMo4-5 to EN 10216-2 Seamless steel tube for elevated temperature
DIN 2391 / EN 10305-1 St35, St45, St52 to DIN 2391; E235, E355 to EN 10305-1 Cold-drawn seamless precision tube
DIN 1629 / EN 10216-1 St37.0, St44.0, St52.0 to DIN 1629; P235TR1, P265TR1 to EN 10216-1 Seamless circular unalloyed steel tubes subject to special requirements

Dimensions and Coating Build-Up

Outside diameter: 13.72 mm to 914.4 mm

Wall thickness: 1.65 mm to 22 mm

Length: 0.5 m to 20 m, random or fixed

Ends: plain, bevelled, threaded and coupled, or grooved

Coating: hot-dip galvanized inside and outside, coating mass agreed at order

Where a general galvanizing specification applies, ISO 1461 requires a minimum mean coating thickness of 85 µm on steel 6 mm and thicker, and 70 µm on steel between 3 mm and 6 mm

Tubes are used for chilled water, drinking water and waste water lines, structural tubing, fluid pipe, boiler pipe, oil and gas transportation pipe, and mechanical structure pipe. Wall thickness is chosen from the design pressure, the corrosion allowance and the stiffness required at support points; the galvanized layer is not counted as a structural contribution.

Frequently Asked Questions

Q: What does high zinc coating mean on a seamless round tube?
It is a hot-dip zinc layer applied at a heavy coating mass agreed between buyer and supplier, so the tube holds sacrificial protection for longer in outdoor, buried or humid service than a light commercial coating would provide.

Q: Is the inside of the tube coated as well?
Yes. Hot-dip galvanizing covers the bore when the tube is dipped with open ends and correct drainage, which matters for water, slurry and gas lines.

Q: Which grades can be supplied galvanized?
The ASTM A53, A106, A179, A192, A210, A213, A312, A333, A335, A519 and A789 families, the API 5L and API 5CT grades, and the DIN 17175, DIN 2391, DIN 1629, EN 10216 and EN 10305 tube grades listed above.

Q: What is the maximum length?
Standard supply runs from 0.5 m to 20 m. Longer single lengths are possible in principle but need an agreed transport and lifting plan.

Q: Can cut ends be left bare?
Cutting exposes bare steel. Ends are normally touched up with a zinc-rich repair coating so that sacrificial protection is restored at the joint face.

Q: How is the coating checked?
Coating mass is determined by the stripping method and local thickness by magnetic gauge, with adhesion confirmed by a bend or impact test taken from a sample of the same production lot.