Grooved round and square carbon steel pipe in a 100x100x3 mm section is a hollow structural product supplied for fluid lines, load-bearing frames and machined components. Each length can be made by a seamless or a welded route and is then end-grooved, so that mechanical couplings replace field welding during installation.
Why a Hollow Section Is the Economical Choice
A hollow section carries bending and torsional loads with far less weight per metre than solid round bar of comparable strength. That ratio is why tube stock is chosen for petroleum drill pipe, automotive transmission shafts, bicycle frames, scaffold tubing and machined rings, where near-net-shape stock shortens machining time and raises material utilisation.
Seamless and Welded Manufacturing Routes
Seamless: the billet is pierced and rolled, so there is no longitudinal weld. Preferred for pressure service and cyclic loading.
Welded (ERW/HFW): strip is formed and seam welded, giving a cost advantage for structural and general engineering lengths.
Grooved ends: a rolled or cut groove accepts a mechanical coupling, allowing fast, flame-free joints and easier maintenance.
API 5L PSL1 Chemical and Mechanical Data
The table lists the specified maximum values for chemical composition and the specified minimum values for tensile and yield strength.
| Grade | C max (%) | Mn max (%) | P max (%) | S max (%) | Tensile min (MPa) | Yield min (MPa) |
|---|---|---|---|---|---|---|
| A | 0.22 | 0.90 | 0.030 | 0.030 | 331 | 207 |
| B | 0.28 | 1.20 | 0.030 | 0.030 | 414 | 241 |
| X42 | 0.28 | 1.30 | 0.030 | 0.030 | 414 | 290 |
| X46 | 0.28 | 1.40 | 0.030 | 0.030 | 434 | 317 |
| X52 | 0.28 | 1.40 | 0.030 | 0.030 | 455 | 359 |
| X56 | 0.28 | 1.40 | 0.030 | 0.030 | 490 | 386 |
| X60 | 0.28 | 1.40 | 0.030 | 0.030 | 517 | 414 |
| X65 | 0.28 | 1.40 | 0.030 | 0.030 | 531 | 448 |
| X70 | 0.28 | 1.40 | 0.030 | 0.030 | 565 | 483 |
API 5L PSL2 Chemical and Mechanical Data
PSL2 grades carry tighter limits on phosphorus and sulphur and add low-temperature toughness testing, which suits sour and low-temperature service.
| Grade | C max (%) | Mn max (%) | P max (%) | S max (%) | Tensile min (MPa) | Yield min (MPa) |
|---|---|---|---|---|---|---|
| B | 0.24 | 1.20 | 0.025 | 0.015 | 414 | 241 |
| X42 | 0.24 | 1.30 | 0.025 | 0.015 | 414 | 290 |
| X46 | 0.24 | 1.40 | 0.025 | 0.015 | 434 | 317 |
| X52 | 0.24 | 1.40 | 0.025 | 0.015 | 455 | 359 |
| X56 | 0.24 | 1.40 | 0.025 | 0.015 | 490 | 386 |
| X60 | 0.24 | 1.40 | 0.025 | 0.015 | 517 | 414 |
| X65 | 0.24 | 1.40 | 0.025 | 0.015 | 531 | 448 |
| X70 | 0.24 | 1.40 | 0.025 | 0.015 | 565 | 483 |
| X80 | 0.24 | 1.40 | 0.025 | 0.015 | 621 | 552 |
Groove Preparation and Section Tolerances
On a 100x100x3 mm square hollow section the outside dimension is 100 mm and the nominal wall is 3 mm, with a formed corner radius set by the manufacturing route. Wall thickness tolerance, squareness and straightness should be agreed against the governing dimensional standard for the relevant product family.
Grooved joints are controlled by three dimensions: the groove diameter, the groove width and the distance from the pipe end to the groove shoulder. These follow the coupling profile in use, so the pipe supplier and the coupling supplier must work from the same profile data.
Standards and Size Ranges for Tubular Sections
| Standard | Scope | Range |
|---|---|---|
| IS 1239 Part I | Mild steel tubes, tubulars and other wrought steel fittings | 15 mm NB to 150 mm NB |
| IS 1161 | Steel tubes for structural purposes | 15 mm NB to 200 mm NB |
| IS 3601 | Steel tubes for mechanical and general engineering purposes | 20.0 x 0.80 mm to 165.10 x 7.00 mm |
| IS 3589 | ERW pipes for water, gas and sewage | 168.3 x 4.00 mm to 219.1 x 7.00 mm |
| IS 9295 | Steel tubes for belt conveyor idlers | 63.5 x 4.00 mm to 219.1 x 7.00 mm |
| IS 4270 | Steel tubes for water wells | 114.3 x 5.00 mm to 219.1 x 7.10 mm |
| IS 7138 | Steel tubes for furniture | 20.0 x 0.60 mm to 60.0 x 2.00 mm |
| IS 4923 | Hollow steel sections for structural purposes | 12.5 x 12.5 x 0.80 mm to 150 x 150 x 6.00 mm and 10 x 20 x 0.80 mm to 150 x 200 x 6.00 mm |
| IS 3074 | Steel tubes for automobile purposes | 19.7 x 1.00 mm to 101.6 x 6.00 mm |
| BS 1387 | Screwed and socketed steel tubes and tubulars | 1/2 in NB to 6 in NB, wall 2.00 mm to 5.40 mm |
| BS 3601 | Steel pipes and tubes for pressure purposes | 1/2 in NB to 6 in NB, wall 2.00 mm to 7.00 mm |
| BS 6323 | Steel tubes for mechanical and general engineering purposes | 21.3 mm to 219.1 mm OD, wall 1.60 mm to 7.00 mm |
Where Grooved Carbon Steel Pipe Is Used
Fluid transmission lines for oil, natural gas, water and slurry duty.
Structural frames, columns, braces and scaffold systems.
Mechanical parts such as drive shafts, machine guards and annular components cut from tube.
Fire protection and utility piping where grooved couplings speed up site assembly.
Frequently Asked Questions
Q: Can the same 100x100x3 mm section be both seamless and welded?
Yes. The section size and the manufacturing route are independent choices; the project specification decides whether a seamless or a welded body is required.
Q: What does a grooved end change compared with a plain end?
A groove lets a mechanical coupling grip the pipe, so joints are assembled without welding; it does not change the pressure rating, which still comes from the pipe specification and wall thickness.
Q: Which API 5L level should be chosen, PSL1 or PSL2?
PSL1 covers standard composition and strength limits, while PSL2 tightens phosphorus and sulphur and adds toughness testing for low-temperature or sour service.
Q: Which grade suits a general structural frame?
Grade B is the usual starting point for structural and general engineering work, with higher X grades selected when additional strength is needed.
Q: How is the section measured in practice?
Square and rectangular hollow sections are stated as outside dimension by outside dimension by wall thickness, so 100x100x3 mm means a 100 mm square with a 3 mm wall.
Q: Is a grooved joint suitable for a buried line?
Mechanical couplings are widely used on above-ground pipework and can serve buried lines when the coupling housing, gasket material and external protection are matched to the soil and the fluid.

