How to improve the adhesion of cold-dip galvanizing?
The key to improving the adhesion of cold-dip galvanizing lies in addressing two key issues: substrate cleanliness and zinc deposition conditions. This requires systematic optimization of pretreatment, electroplating parameters, and post-treatment, while also avoiding adhesion defects caused by improper operation.
1. Core Optimization Direction: Substrate Pretreatment (the Basis for Determining Adhesion)
The bond between the cold-dip galvanizing layer and the substrate is essentially the uniform deposition of zinc ions on a clean substrate surface. Oil, scale, rust, or impurities on the substrate surface can directly lead to "false adhesion" of the zinc layer (i.e., a barrier layer between the zinc layer and the substrate), making it susceptible to subsequent detachment. Therefore, pretreatment must be "oil-free, rust-free, scale-free, and impurity-free."
1. Thorough Degreasing: Remove grease and organic matter from the substrate surface. Grease (such as processing lubricants and rust preventatives) forms a hydrophobic layer on the substrate surface, hindering zinc ion adhesion and must be completely removed. A two-step degreasing method is recommended:
Step 1: Alkaline Chemical Degreasing
Use a mixture of 5%-10% sodium hydroxide (NaOH) and 2%-5% sodium carbonate (Na₂CO₃) at 50-60°C for 10-15 minutes. Alkaline solutions emulsify oils and break them down into water-soluble substances, making them suitable for removing most mineral oils and animal and vegetable oils.
Note: After soaking, rinse with running water 2-3 times to prevent residual alkaline solution from corroding the substrate.
Step 2: Electrolytic Degreasing (for heavily oiled or complex surfaces)
If the rod surface has stubborn oil stains (such as extreme pressure lubricant residue from processing), apply 10-15V DC to the degreasing tank (with the substrate connected to the cathode). The hydrogen and oxygen bubbles generated by the electrode reaction "strip" the oil from tiny crevices. Keeping the electrolysis time to 5-8 minutes can increase the oil removal rate to over 99%. 2. Thorough Rust/Scale Removal: Exposing the Fresh Metal Surface
The scale (Fe₃O₄, Fe₂O₃) and rust (FeO (OH)・nH₂O) on the substrate surface are loose structures that cannot be bonded to the zinc layer. Therefore, thorough removal is essential. Two main methods are recommended:
Acid Cleaning (Suitable for routine mass production of parts)
Use a 15%-20% hydrochloric acid (HCl) solution and soak for 8-12 minutes at room temperature (or a 5%-8% sulfuric acid solution at 40-50°C for 10-15 minutes). During the pickling process, add 0.5%-1% of a corrosion inhibitor (such as hexamine) to prevent excessive corrosion of the substrate (to avoid surface roughness caused by "over-acidification"). After pickling, rinse with running water until the pH reaches neutral (6-7 using pH test paper) before proceeding to the next step. Sandblasting for Rust Removal (Suitable for High-Quality Surfaces or Complex Parts)
For galvanized round bars requiring a fine surface, sandblasting with 80-120 mesh quartz sand or corundum using 0.5-0.8 MPa compressed air can be used. This physical impact removes scale and rust while creating a uniform "rough surface" (surface roughness Ra 1.6-3.2 μm) on the substrate surface. This roughened surface increases the contact area between the zinc layer and the substrate, improving bonding strength by 20%-30%. However, it is important to note that the electroplating process must begin within 2 hours after sandblasting to avoid secondary oxidation of the substrate.
3. Activation Treatment: Eliminate Residual Impurities and Enhance Zinc Ion Adsorption
After pickling or sandblasting, trace amounts of impurities such as iron and chloride ions may remain on the substrate surface, requiring further purification through activation. This is typically done by soaking in a 1%-2% dilute hydrochloric acid or sulfuric acid solution at room temperature for 1-2 minutes. This removes the extremely thin surface oxide film, leaving the substrate surface "fresh and active," providing good attachment points for zinc ion deposition. After activation, it must be placed in the electroplating tank immediately to avoid contact with air and secondary oxidation.

