Why Coating Weight Is the First Cost Lever
In continuous hot-dip galvanizing the zinc layer is usually the largest controllable cost after the steel substrate. The coating mass designation used in EN 10346 states the total mass applied to both sides in grams per square metre, so Z100 corresponds to roughly 7 micrometres of zinc per side and Z275 to roughly 19 micrometres per side. Moving from Z275 to Z140 removes a large amount of zinc without changing the substrate, but this only works if corrosion performance is preserved by other means. The measures below act on the process, the substrate and the coating system rather than on the zinc alone.
| Coating designation | Total mass, both sides | Approximate thickness per side | Typical application |
|---|---|---|---|
| Z40-Z60 | 40-60 g/m² | 3-4 µm | Dry interior parts with passivation, non-exposed components |
| Z100 | 100 g/m² | About 7 µm | General indoor and sheltered outdoor use, base for color coating |
| Z140-Z180 | 140-180 g/m² | 10-13 µm | Semi-exposed building components, appliances in humid rooms |
| Z275 | 275 g/m² | About 19 µm | Industrial, coastal and long-life structural sheet |
1. Tighten the Hot-Dip Process Parameters
Bath temperature: hold the zinc bath in the 440-460 °C window. Temperatures above roughly 470 °C thicken the coating, roughen the surface and increase zinc consumption for no gain in protection.
Dipping time: 10-30 seconds, adjusted to sheet thickness. Longer immersion grows the iron-zinc alloy layer and makes the coating harder and less formable.
Pull-out speed: keep it steady. Oscillation and speed steps cause run-off beads and local zinc accumulation, which forces the average coating mass above the target.
Air knives: nozzle gap, wiping pressure and distance to the strip are the direct controls on coating mass. With closed-loop control, the mass tolerance can be held to roughly plus or minus 10 percent instead of plus or minus 20 percent, which is where most of the saving is found.
Bath chemistry: an aluminium addition in the range of 0.15-0.25 percent improves bath fluidity, gives a thinner and more uniform zinc layer, and keeps the alloy layer under control. Dross and top skimmings must be removed, because they print into the coating and create local thick spots.
2. Improve the Substrate Before Galvanizing
Scale and oil removal: a combined pickling and electrolytic degreasing sequence removes oxide film and rolling oil. Residual oxide between steel and zinc prevents bonding, and an unbonded coating has to be made thicker to compensate.
Surface roughness: roughness controls how zinc drains and solidifies. A skin-pass with a fine work roll, around 0.2 micrometres of roll roughness, produces a smoother surface and more uniform coverage. For the same protective effect, coating mass on a smooth surface can be reduced by roughly 10-15 percent compared with a rough, unskimmed surface.
Avoid over-pickling: excessive pickling creates pits and hydrogen pick-up that show up later as adhesion defects.
3. Get More Protection from the Same Zinc
| Post-treatment | How it helps | Practical note |
|---|---|---|
| Trivalent chromium passivation | Thin conversion film blocks water and oxygen and slows the formation of white rust | A Z50 coil with passivation can reach salt spray life well beyond the roughly 100 hours of an unpassivated Z50 |
| Chromium-free passivation: silane, titanate or ceramic | Chemically bonds to the zinc and forms a dense organic-inorganic barrier | A Z60 with silane passivation approaches the corrosion performance of unpassivated Z100 without heavy metals |
| Phosphating plus paint | Phosphate crystals of 2-5 µm anchor an organic coating and add a further barrier | Z60 with phosphate plus a 20 µm epoxy coating can outperform bare Z150 in the same exposure |
| Color coating | The organic coating becomes the primary barrier and the zinc a sacrificial backup | With a 20-25 µm topcoat the zinc layer can be reduced to Z50-Z80 instead of Z100 or more |
Hexavalent chromium passivation is restricted under RoHS and is being phased out in most markets. Specify trivalent chromium or a chromium-free system so that the coating reduction does not create a compliance problem later.
4. Match Coating Mass to the Real Exposure
| Service environment | Coating route that is normally sufficient |
|---|---|
| Dry interior: appliance backs, cabinet frames, furniture, dry plumbing areas | Z40-Z60 with chromium-free passivation; the rust-free life still exceeds the life of the product itself |
| Humid interior and sheltered outdoor | Z100-Z140 with passivation, or Z50-Z80 under an organic color coating |
| Industrial, urban and coastal exposure | Z275, or Z100-Z140 beneath a full color coating system with a suitable topcoat |
| Deep-drawn and heavily formed parts | Thinner coatings crack and flake less on tight bends, so a lower mass with passivation often forms better as well as cheaper |
5. Verify the Reduction Before Releasing It
Coating mass: determine it gravimetrically to ISO 1460 rather than relying on a single gauge reading, and confirm that the three-point profile across the strip is within tolerance.
Corrosion: run neutral salt spray to ISO 9227 for a quick ranking, then a cyclic test that reflects the real environment, because a thin coating performs differently under wet-dry cycling than under constant fog.
Formability: check bend, T-bend and impact on the reduced coating, since the point of a thinner layer is frequently better forming behaviour.
Adhesion: cross-cut and tape tests before and after forming confirm that the thinner coating still bonds through the process.
Frequently Asked Questions
Q: How much coating weight can be saved without losing performance?
For dry indoor parts, moving from Z80-Z100 to Z40-Z60 with good passivation is common. For exposed parts, the saving usually comes from replacing part of the zinc with an organic coating rather than from simply reducing zinc.
Q: Is a thinner zinc coating always cheaper overall?
Not always. It saves zinc and often improves forming, but it reduces the reserve that protects cut edges and scratches. The saving should be judged on total cost of ownership, including any change in exposure class or warranty.
Q: Can a thinner coating pass the same salt spray requirement?
Yes, if it is denser. A uniform Z50 with passivation can outlast a porous Z80, because salt spray life depends far more on porosity and uniformity than on total zinc mass.
Q: Does aluminium in the zinc bath reduce coating weight?
It improves fluidity so that the coating drains more evenly, which allows a lower average mass with the same minimum thickness at any point of the strip. The addition must stay within the narrow range recommended for the bath.
Q: Why does surface roughness matter so much?
Zinc collects in the valleys of a rough surface and drains from the peaks, so roughness forces a higher average mass to guarantee a minimum local thickness. A smoother, skimmed surface delivers the same protection with less zinc.
Q: Is chromium-free passivation as good as chromate?
For most architectural, appliance and general industrial use, silane or titanate systems give equivalent or better performance under an organic topcoat, and they avoid restricted substances. For maximum bare-corrosion life, a slightly higher coating mass may be needed to match chromate.
Q: How is the coating mass actually measured?
The reference method is gravimetric: a measured sample is stripped of zinc and reweighed to obtain the mass per unit area, as described in ISO 1460. Magnetic and X-ray gauges are used for fast line control and for the three-point profile.

