DC01, DC03, DC04 and SPCC Cold Rolled Steel Coils: Forming Grades vs Structural Grades

Sep 11, 2025 Leave a message

A Coil Range Built Around Two Different Jobs

Cold rolled steel coils in the 0.5 mm to 5 mm range serve two separate purposes, and the grade list on a mill certificate usually mixes them. The DC and SPCC families are forming grades: they are specified for how well the sheet bends, draws and stretches. SS400, St37, A36 and Q235B are structural grades: they are specified for minimum yield strength and are used where the finished part carries load. Choosing the wrong family is the most common specification error in this size range, because the two look similar in a mill but behave very differently in a press or under a load.

Forming Grades: DC01, DC03 and DC04

DC01 (EN 10130) - the basic grade of the DC family, formerly designated St12 or FeP01. It handles simple forming operations such as bending, coining, beading and light drawing. Engineers often quote it under the older CR4 designation, which refers to the same commercial quality.

DC03 (EN 10130) - a drawing-quality grade with improved ductility and a more consistent grain structure, used where a single drawing operation has to be reliable across a long production run.

DC04 (EN 10130) - a deep-drawing steel with excellent performance under all types of deformation. It suits high forming requirements: deep cups, complex panels and parts that would tear or thin out in a lesser grade.

Within the same family, going from DC01 to DC04 buys forming depth at the cost of strength, so the correct choice is set by the severity of the part, not by a preference for a higher grade.

Japanese Equivalents: SPCC, SPCD and SPCE

SPCC under JIS G3141 is the commercial-quality cold rolled grade and sits alongside DC01 in forming terms; SPCD corresponds to a drawing-quality material and SPCE to deep drawing. They are metrically interchangeable with the DC grades in ordinary fabrication, but a direct substitution still needs a check on the mechanical property table of the specific mill certificate, because tolerance and surface requirements can differ between the two standards.

Structural Grades: SS400, Q235B, St37 and A36

Grade Standard Minimum yield strength Tensile range
Q235B GB/T 700 235 MPa 370–500 MPa
SS400 JIS G3101 245 MPa 400–510 MPa
St37 DIN 17100, superseded by S235JR (EN 10025-2) 235 MPa 360–510 MPa
A36 ASTM A36 250 MPa 400–550 MPa

The yield values apply to the ordinary thickness range up to about 16 mm; heavier sections are subject to lower specified minima in the same standards. Where a part needs both corrosion resistance and a structural minimum, these coils are the substrate for hot-dip galvanizing, and the coating is specified separately to EN ISO 1461 or to the strip coating class of EN 10346.

Thickness, Width and Dimensional Standards

The 0.5 mm to 5 mm band covers most light fabrication. Common stock thicknesses are 0.5, 0.6, 0.7, 0.8, 0.9, 1.0, 1.2, 1.5, 2.0, 2.5, 3.0, 4.0 and 5.0 mm; widths are set by the mill's rolling programme and the parent coil, and coils are wound with a 508 mm or 610 mm inner diameter. Thickness tolerance is not something to assume: uncoated cold rolled flat product is specified to EN 10131, and the equivalent route in North America is ASTM A1008/A1008M with its general requirements. A tolerance quoted to the wrong standard can be the difference between a coil that runs and one that is rejected at goods-in.

Choosing Between the Two Families

Start from the process, then the load. If the part is formed and then carries no structural duty, a DC or SPCC grade is correct; if it carries load, a structural grade is required regardless of how easy it is to bend.

Match forming severity to grade. A shallow bend runs on DC01; a deep drawn enclosure usually needs DC04 or SPCE.

Check equivalence claim by claim. Cross-standard substitution between EN, JIS and GB grades should always be confirmed against the mechanical properties on the certificate.

Decide the surface route early. Whether the coil is to be left bare, painted or galvanized affects the grade and the coating class that should be ordered.

FAQ

Q: What is DC01 steel and what is it used for?
DC01 to EN 10130 is the basic cold rolled forming grade, previously called St12 or FeP01, and is often quoted as CR4. It is used for simple forming: bending, coining, beading and light drawing.

Q: What is the difference between DC01 and DC04?
Both are defined in EN 10130, but DC04 is a deep-drawing grade with markedly better ductility. DC01 suits basic forming, while DC04 suits high forming requirements such as deep cups and complex panels.

Q: Is SPCC the same as DC01?
They occupy the same commercial-quality position, but SPCC is defined in JIS G3141 and DC01 in EN 10130, so the two are not automatically interchangeable. Substitution should be checked against the mechanical properties on the mill certificate.

Q: Can SS400 or Q235B be used for deep drawing?
No. These are structural grades specified for minimum yield strength, not for formability. They bend and fabricate well, but a deep-drawing operation calls for a DC or SPCC grade.

Q: What thicknesses are available in this range?
Coils are normally supplied between 0.5 mm and 5 mm, with stock thicknesses including 0.6, 0.8, 1.0, 1.2, 1.5, 2.0, 3.0 and 4.0 mm. Thickness tolerance is specified to EN 10131 or ASTM A1008/A1008M.

Q: How should these coils be stored before processing?
Flat, dry and off the floor, with the wrap intact. Cold rolled surfaces mark easily, and moisture between wraps causes edge rust that shows up as a surface defect after forming.