What DC01 Cold Rolled Steel Sheet Metal Is
DC01 is the basic grade of the European DC family of cold-rolled low-carbon flat products, supplied under EN 10130 with the material number 1.0330. It is the direct successor to the former St12 and FeP01 designations, which were withdrawn when DIN 1623 was replaced by EN 10130. In workshops the grade is often called CR4, although CR4 is commercial shorthand rather than a standardised grade name. DC01 is specified for simple cold forming such as bending, coining, beading and light drawing, which makes it the most widely used cold-rolled sheet in general engineering.
Mild steel sheet metal in 2.4 mm thickness in cold-rolled quality is a common request for brackets, panels, cabinets and general fabrication, where a smooth surface and consistent thickness matter more than extreme drawability.
Grades, Designations and Equivalents
| Designation | Standard | Notes |
|---|---|---|
| DC01 (1.0330) | EN 10130 | Basic forming grade, replaces St12 and FeP01 |
| DC03 | EN 10130 | Improved formability for difficult profiling, replaces St13 |
| DC04 | EN 10130 | Deep drawing grade, replaces St14 |
| SPCC | JIS G3141 | Japanese commercial-quality cold-rolled equivalent |
| CS Type B | ASTM A1008/A1008M | US commercial steel for general forming |
The designation is built from the delivery condition (D for cold rolled) and the forming class, so DC01 and DC04 are the same steel family with different forming capability rather than different alloy systems. Where a drawing calls for "cold reduced mild steel" without a grade, DC01 is the usual default, but deep-drawn parts should always be re-checked against DC03 or DC04 requirements before release to production.
2.4 mm Thickness in Cold Rolled Sheet and Coil
EN 10130 covers cold-rolled flat products from 0.35 mm up to below 3 mm, so 2.4 mm sits within the standard range; at the upper end of that range the material is normally supplied as cut sheet or as narrow coil. Dimensional tolerances for metric orders are taken from EN 10131, while inch-pound orders are quoted to ASTM A568/A568M. Two practical points matter at this thickness:
Coil set and crossbow increase with thickness, so sheets are usually levelled or tension-levelled before laser cutting or pressing.
Flatness, edge condition and camber become more critical than for thin gauges because forming loads are higher and springback is greater.
Surface quality is ordered as finish A (normal) or finish B (improved, suitable for visible painted parts), and the surface appearance may be agreed as bright, matt or dull according to the customer requirement.
Mechanical Properties and Formability
| Grade | Yield strength Re (MPa) | Tensile strength Rm (MPa) | Elongation A80 min (%) |
|---|---|---|---|
| DC01 | 140-280 | 270-410 | 28 |
| DC03 | up to 240 | 270-370 | 34 |
| DC04 | up to 210 | 270-350 | 38 |
Lower yield strength and higher elongation mean better drawability. DC01 therefore covers bending and light drawing, DC03 covers difficult profiling, and DC04 is used where deep drawing is required. If a part needs more severe stretching than DC04 allows, the interstitial-free DC05 and DC06 grades are selected instead. Mechanical properties are verified by tensile testing to EN ISO 6892-1, and chemical requirements for the family limit carbon, manganese, phosphorus and sulphur while requiring a minimum aluminium content for a fully killed steel.
Typical Applications and Processing
Brackets, supports and general sheet-metal fabrication in 2.4 mm gauge
Electrical enclosures, cabinets and control boxes
Shelving, ducting, panels and housings with a painted finish
Components that are subsequently formed, welded and powder coated
DC01 welds readily by spot, seam and arc processes, and its low carbon content keeps hardness in the heat-affected zone low, so tool wear in downstream machining stays predictable. After degreasing it accepts paint, powder coating and zinc-rich primers well, and it can be bent to tight radii because of its high ductility. Sharp 180 degree folds across the rolling direction should still be checked for cracking on a thick gauge such as 2.4 mm, since the outer fibre strain increases with thickness. For parts that will be exposed to weather without painting, a coated product such as hot-dip galvanized coil or an electro-zinc coated sheet should be considered instead of bare cold-rolled sheet.
FAQ
Q: Is DC01 the same as CR4?
Practically, yes. CR4 is a trade shorthand for cold-reduced mild steel that is normally supplied as DC01, but the formal requirement is always the EN 10130 grade.
Q: Can DC01 be supplied in 2.4 mm thickness?
Yes. EN 10130 covers thicknesses from 0.35 mm up to below 3 mm, and 2.4 mm is supplied as cut sheet or narrow coil with tolerances to EN 10131.
Q: What is the difference between DC01 and DC03?
DC01 is for simple forming such as bending and beading. DC03 has a lower yield strength and higher elongation, so it suits difficult profiling and moderate deep drawing.
Q: What is the former name of DC01?
St12, and FeP01 in the earlier designation system. Both were replaced when DC01 was introduced under EN 10130.
Q: Does cold-rolled DC01 rust outdoors?
Yes. Cold-rolled sheet has no metallic coating, so it needs painting, oiling, or a galvanized or zinc-coated alternative for outdoor service.
Q: How is DC01 tested before delivery?
Tensile properties are verified to EN ISO 6892-1, and dimensions, flatness and surface finish are checked against EN 10131 and the agreed surface quality class.

