Most stamped parts are made from low-carbon steel with less than about 0.25% carbon and a tensile strength below roughly 650 N/mm², because higher strength grades lack the ductility that dies need. Common base materials include SPCC and 1010 type steels for general stamping, with SPCD, SPCEN, DC03 and DC04 families for deeper draws. But the grade name only opens the door; the actual stamping result is decided by measurable parameters that the mill certificate can verify. This article explains those parameters so that buyers and tool engineers speak the same language.
Mechanical properties that matter
Four tensile quantities control stamping: tensile strength sets the press force and springback level, yield strength decides how easily the material starts to flow, elongation indicates the general ductility, and hardness correlates with tool wear and edge quality. For drawing work the yield-to-tensile ratio is more informative than either value alone: a low ratio, typically below 0.7, means the material yields easily and hardens substantially during the draw, which reduces springback and improves shape retention. The certificate should show all four values for the ordered thickness, because thin and thick strip of the same grade behave differently.
Microstructural condition and spheroidizing
The microstructure of the steel, especially the form of the carbides, sets the upper limit of formability. For severe forming, the cementite should be spheroidized, because globular carbides do not act as stress raisers the way lamellar pearlite does. Spheroidizing annealing is therefore a standard requirement for medium-carbon stamping steels and for parts that are cold formed after hardening processes. A microstructure check by microscopy is a practical acceptance test when splits or edge cracking appear in an otherwise correct chemical analysis.
| Parameter | Meaning | Typical target for deep drawing |
|---|---|---|
| Yield ratio | yield over tensile strength | below about 0.7 |
| Elongation | total ductility, especially uniform elongation | high, grade-dependent |
| n-value | strain hardening exponent | 0.18 and above for drawing grades |
| r-value | plastic strain ratio, resistance to thinning | 1.5 and above for drawing grades |
| Hardness | resistance to indentation and wear | matched to tooling and edge quality |
| LDR | limiting drawing ratio from cup test | rises with r-value |
| CCV | conical cup value, for thickness 0.5-1.6 mm | smaller value, better drawability |
The n-value and r-value pair
The strain hardening exponent n describes how the material strengthens during deformation; a high n-value spreads strain over a wider area and delays necking, which is essential for stretch forming and for parts that combine drawing with stretching. The plastic strain ratio r describes the resistance to thinning in the thickness direction; a high r-value allows deeper cups before the wall thins to failure. Deep-drawing grades guarantee minimum r and n values, for example DX54D guarantees r90 of 1.6 and n90 of 0.18, and the combination of the two parameters is the best single predictor of draw performance.
Aging behaviour and delayed cracking
Stamped parts can crack days after forming, a phenomenon called aging cracking or delayed fracture. It happens when residual tensile stress from the draw is high and the material is susceptible to strain aging; the crack is typically longitudinal along the wall of a deep-drawn cup. The countermeasures are to reduce residual stress by die design and lubrication, to use non-aging or low-aging steel with controlled nitrogen, and to inspect parts after a holding period before finishing. Buyers who stamp critical parts should require a non-aging specification or an aging test in the delivery condition.
Formability tests: LDR and CCV
The limiting drawing ratio LDR is measured with a cylindrical cup test: the ratio of the largest blank diameter that can be drawn without failure to the punch diameter, LDR equals D divided by dp. A higher LDR means deeper cups are possible, and LDR correlates positively with the r-value. The conical cup value CCV is measured by drawing a conical cup and recording the resulting cup edge diameter; a smaller CCV indicates better drawability, and the test is applied to sheet thicknesses of about 0.5-1.6 mm. Both tests belong on the qualification list for new suppliers, because they capture behaviour that the tensile test alone does not show.
Frequently Asked Questions
What carbon content is typical for stamping steel? Most stamping steels contain less than about 0.25% carbon, and deep-drawing grades such as DC03, DC04 and SPCEN hold carbon at 0.10% or below to reach the ductility the dies need.
Why is the yield ratio important for stamping? low yield-to-tensile ratio means the steel yields easily and hardens during the draw, which reduces springback and improves shape retention; a ratio above about 0.7 signals limited drawability.
What is the difference between n-value and r-value? The n-value measures strain hardening and governs stretching and strain distribution, while the r-value measures resistance to thickness thinning and governs how deep a cup can be drawn; both are guaranteed for deep-drawing grades.
What causes cracks that appear days after stamping? They are aging cracks caused by high residual tensile stress combined with strain aging; countermeasures include lower residual stress, non-aging steel and a holding-period inspection before finishing.
How is the LDR test performed? cylindrical cup is drawn from progressively larger blanks until failure, and the LDR is the ratio of the largest successful blank diameter to the punch diameter; a higher LDR means deeper draws are possible.
Which steel should I choose for a complex deep-drawn part? Start from the draw severity: DC04 or SPCEN for uncoated deep draws, DX54D or DX56D for coated parts, and verify the certificate r and n values plus an LDR test from the supplier before tooling is committed.

