CR4: The Trade Name for Cold Reduced Steel
CR4 stands for cold reduced steel sheets. The term comes from the rolling process itself: hot rolled strip is pickled and then cold rolled to final thickness, which gives the product a smoother surface and a finer finish than hot rolled material. This surface quality is what makes cold reduced steel suitable for parts that will be painted, powder coated or exposed to view. Typical applications include fuel tanks, tool boxes, drip pans, trailer siding, lockers, office furniture and general sheet metal work where a clean, flat, paintable surface is required.
DC01: The Workhorse Cold Rolled Grade
DC01 is the designation defined in EN 10130 for cold rolled low carbon steel flat products for cold forming. In the trade, DC01 is very often referred to simply as CR4, and the two names point to the same material. DC01 is supplied in thicknesses from about 0.9 mm up to 3 mm as standard stock, with wider and thinner ranges available by agreement with the mill. It is delivered annealed and skin-passed, which restores ductility after cold rolling and gives the flatness and surface quality needed for bending, punching and deep drawing of simple parts. When the same material is supplied with an electrolytic zinc coating, it appears in the specifications as DC01+ZE, defined in EN 10152.
SPCC: The JIS Cold Rolled Standard
SPCC is the corresponding Japanese designation from JIS G3141 for cold rolled carbon steel sheet and strip of commercial quality. DC01 and SPCC sit at the same quality level and are frequently treated as equivalents in international trade; the choice is normally dictated by which standard the buyer's market uses. SPCC is also the base material for galvanized products such as SGCC, where the cold rolled sheet is hot-dip zinc coated. Buyers in South Asian and Middle East markets often request inspection certificates issued under JIS, KS or BIS-recognised schemes; the practical point is to state the governing standard and the certificate type on the purchase order so the mill issues the right documents.
DC04: The Deep Drawing Grade
DC04 is a deep drawing steel of the DC grade family, also defined in EN 10130. It has excellent deep drawing properties under all types of deformation and is suitable for high forming requirements such as multi-stage drawn parts, kitchen sinks, automotive inner panels, and appliance housings with complex geometry. The grade numbering reflects the drawability: DC01 is suitable for simple bending and shallow forming, DC03 adds drawability, DC04 provides deep drawing quality, and DC05/DC06 go further for very severe forming with increased cost. If a part tears or necks during drawing trials, moving from DC01 to DC04 is the usual first step.
Selecting the Right Cold Rolled Grade
| Designation | Standard | Typical Thickness | Typical Use |
|---|---|---|---|
| DC01 / CR4 | EN 10130 | 0.9-3 mm | Panels, tool boxes, trailer siding, general forming |
| SPCC | JIS G3141 | 0.3-3.2 mm | Furniture, cabinets, base for SGCC galvanizing |
| DC03 | EN 10130 | 0.5-3 mm | Drawn parts with moderate forming severity |
| DC04 | EN 10130 | 0.5-3 mm | Deep drawn parts, sinks, automotive components |
Surface quality is specified separately from the grade. Standard cold rolled surface is suitable for most industrial use; for high-gloss paint finishes, the brighter surface class should be requested, and the strip should be protected against scratches and rust in storage. Prime material is normally delivered with lightly oiled surfaces to resist corrosion during transport.
Buyer's Checklist for Prime Cold Rolled Coil and Sheet
1. State the standard (EN 10130, JIS G3141 or equivalent) and the grade with the exact thickness and width. 2. Confirm the delivery condition: annealed and skin-passed, with the required surface finish and oiling. 3. Agree the certificate: mill test certificate with heat number, chemical analysis and tensile results, plus third-party inspection where the project demands it. 4. Check tolerances: thickness, width and flatness tolerances differ between standards and affect downstream tooling. 5. Verify the coil weight and inner diameter so the material fits the customer's decoiling line.
Frequently Asked Questions
Is DC01 the same as CR4? In the trade, yes. CR4 is the older trade name for cold reduced steel, and DC01 is the EN 10130 designation for the same product. A DC01 coil is commonly referred to as CR4 in quotes and datasheets.
What thicknesses of DC01 are normally available? Standard stock typically covers 0.9 mm up to 3 mm, with thinner gauges from about 0.3 mm and thicker material available by mill agreement depending on the width.
What is the difference between DC01 and SPCC? DC01 is defined in EN 10130, SPCC in JIS G3141. They are equivalent commercial-quality cold rolled grades; the choice is usually made by the market standard and the certificate required by the buyer.
Is DC04 suitable for deep drawing? Yes. DC04 is specifically a deep drawing grade with excellent formability under all types of deformation, making it the standard choice for parts that require multi-stage drawing.
Is cold rolled coil supplied annealed? Yes. Prime cold rolled coil is supplied annealed and skin-passed, which restores ductility after the cold reduction and gives the flatness and finish required for bending and forming.
Can DC01 be welded and painted? Yes. DC01 welds and paints well; for painted panels the surface should be degreased and phosphated first to guarantee paint adhesion and corrosion resistance.

