Carbon Steel Plate Grades Compared: Q235, Q355, ASTM A36, A283, A516 and DC01

Jan 30, 2026 Leave a message

Carbon steel plate is quoted in more grade names than any other steel product, and most of the names map onto a small set of real materials. The confusion is not about chemistry, it is about standard systems: GB designations such as Q235 and Q355, ASTM designations such as A36, A283 and A516, and the cold rolled EN family represented by DC01 all describe different product families with different testing philosophies. This article aligns the grades side by side, so a buyer can convert a drawing into a correct purchase order without guesswork.

The Grade Families and Their Standards

Q235 is the general structural carbon steel of GB/T 700, the Chinese equivalent of the international structural workhorse. Q355 is a high-strength low-alloy structural steel of GB/T 1591, comparable in strength class to the European S355 of EN 10025-2. ASTM A36 is the American structural carbon steel plate and bar standard. ASTM A283 covers low and intermediate tensile strength carbon steel plates for general and pressure applications. ASTM A516 covers carbon steel plates for pressure vessels at moderate and lower temperature service. DC01 is the cold rolled forming grade of EN 10130, a different product family entirely, thin sheet for cold forming rather than structural plate. The first rule of cross-referencing is to identify which family the drawing actually needs.

Mechanical Data Side by Side

Grade Standard Yield (min, MPa) Tensile (MPa) Elongation (min %)
Q235B GB/T 700 235 370 - 500 26
Q355B GB/T 1591 355 470 - 630 20 - 22
ASTM A36 ASTM A36/A36M 250 400 - 550 20 - 23
ASTM A283 C ASTM A283/A283M 205 380 - 515 22 - 25
ASTM A516-70 ASTM A516/A516M 260 485 - 620 17 - 21
DC01 (sheet) EN 10130 140 - 280 270 - 410 28

The values are the guaranteed minimums for the common thickness ranges; elongation varies with thickness and test direction, so the mill certificate for the ordered gauge is the binding document. The table shows the real structure of the market: Q235 and A36 serve ordinary structural duty, Q355 and the European S355 serve higher-strength framing, A283 is a lower-cost general plate, A516 is the pressure vessel material, and DC01 is a forming sheet, not a plate grade.

Impact Toughness: The Letter That Changes Everything

The letter after the GB designation is an impact toughness grade, not a strength grade. Q235A and Q355A carry no impact guarantee; Q235B and Q355B guarantee a Charpy V-notch value at room temperature; Q355C, D and E guarantee 34 joules at 0, minus 20 and minus 40 degrees Celsius respectively. For welded structures in cold climates, dynamic loading and safety-critical service, the impact grade matters more than the yield number, because a plate that passes the tensile test can still fail by brittle fracture at a weld. The same logic applies across systems: S355JR in EN 10025-2 guarantees 27 joules at 20 degrees Celsius, S355J2 guarantees 27 joules at minus 20 degrees Celsius, and A516 pressure vessel plates are ordered with their own impact testing options for low-temperature duty.

Common Specification Errors to Avoid

Three errors appear constantly in enquiries. First, treating Q355 as stainless steel: Q355 is a high-strength low-alloy carbon steel, and it rusts like any carbon steel, so corrosion service demands a coating or a stainless grade, not Q355. Second, ordering DC01 where a structural plate is needed: DC01 is a thin cold rolled forming sheet, and a 10 mm structural plate requirement must go to a plate grade such as Q235, A36 or S235. Third, substituting on the yield number alone: a 355 MPa grade is not automatically weldable or impact-certified, the impact grade letter and the welding procedure must follow the drawing. When a project specifies an ASTM or EN grade and the mill proposes a GB equivalent, the equivalence must be checked against the full set of requirements, chemistry, yield, tensile, impact and thickness range, not just the yield number.

Selection Logic for the Buyer

Start from the service: general building structure, choose Q235, A36 or S235 depending on the governing code. Higher loads and longer spans, move to Q355 or S355 with the impact letter matched to the service temperature. Pressure vessels and low-temperature duty, go to A516 or the corresponding EN pressure grades with the impact testing specified. Thin parts that are bent, stamped or drawn, come down to the cold rolled family, DC01 and above. In every case, write the standard and grade into the order exactly as the drawing states, request the mill test certificate per EN 10204, and let the certificate, not the sales name, settle the equivalence debate.

Frequently Asked Questions

Is Q355 stainless steel?

No. Q355 is a high-strength low-alloy carbon steel per GB/T 1591, and it rusts like any carbon steel without protection. The confusion appears because some supplier descriptions call it stainless loosely; the certificate always states the actual standard and grade.

What is the difference between Q235B and Q355B?

Q355B has a minimum yield of 355 MPa against 235 MPa for Q235B, and a higher tensile band, which allows lighter sections for the same load. Q235B is the economy structural grade; Q355B is specified where strength saves material and weight.

How does ASTM A36 compare with Q235?

Both are general structural carbon steels with similar yield and tensile values, and they are commonly treated as equivalents. A36 guarantees 250 MPa yield and 400 - 550 MPa tensile, Q235 guarantees 235 MPa and 370 - 500 MPa, so the mapping is close but not identical, and the governing project code decides which is acceptable.

When should ASTM A516 be used instead of A36?

A516 is a pressure vessel plate with controlled chemistry and impact options for moderate and low-temperature service. Use it for pressure vessels, boilers and storage tanks, where A36 general structural plate is not accepted by the pressure codes.

Can Q355 meet dynamic load requirements such as operating tables or machinery frames?

Yes, when the impact grade is right. Q355C, D and E guarantee 34 joules at 0, minus 20 and minus 40 degrees Celsius respectively, which covers dynamic and cold-service duty. Grade A without impact testing should not be used for such applications.

What does the letter B or D mean in Q355B or Q355D?

The letter is the impact toughness grade: B guarantees room-temperature impact energy, C at 0 degrees Celsius, D at minus 20 and E at minus 40. It does not change the strength, and it is the decisive requirement for welded structures in cold or dynamic service.