What Regular and Zero Spangle Mean
Hot-dip galvanized steel coil is produced by passing annealed cold-rolled strip through a molten zinc bath at about 450–460 °C, wiping the coating to the required mass and cooling it. As the zinc solidifies, crystals grow across the surface and form the visible pattern known as spangle. Regular spangle is the natural, unrestricted pattern; zero spangle, sometimes called minimized spangle, is produced by skin-passing the strip after the zinc has solidified, which flattens the crystal relief and leaves a smooth, uniform, semi-matt surface.
The choice is largely a matter of appearance and downstream processing, not of corrosion performance. The zinc mass, the coating adhesion and the cleanliness of the substrate decide how well the coil resists corrosion and forming.
Structure of a Galvanized Coil
Substrate: cold-rolled low-carbon steel, typically DC01 or an equivalent drawing quality grade, supplied to a controlled thickness tolerance.
Zinc coating: a metallurgically bonded layer applied on both surfaces. Coating mass is quoted either as a total for both surfaces, as in Z100 or Z275, or as a class such as G90 in ASTM A653.
Surface treatment: chromate-free passivation, oiling, or an anti-fingerprint film applied on the line to prevent white rust in storage and to condition the surface for painting.
Skin pass: a light rolling pass after galvanizing that improves flatness and surface appearance, and creates the zero spangle finish when the mill specifies it.
DX51D and Related Grades
DX51D is defined in EN 10346 as a bending and forming grade for hot-dip coated steel, with low carbon content for good ductility and weldability. The same standard covers DX52D, which offers higher elongation, and DX53D, the deep-drawing grade.
| Grade | Yield strength | Tensile strength | Elongation A80 | Typical use |
|---|---|---|---|---|
| DX51D+Z | 140–320 MPa | 270–500 MPa | min 22 % | General bending and forming, panels and profiles |
| DX52D+Z | 140–300 MPa | 270–420 MPa | min 26 % | Drawing of moderate depth, appliance parts |
| DX53D+Z | 140–260 MPa | 270–380 MPa | min 30 % | Deep drawing, complex pressings |
In the Japanese system, SGCC is broadly comparable to DX51D+Z for general forming, while SGCD1 and SGCD2 correspond to the more formable grades. DC51D+Z is a separate designation built on a DC01 cold-rolled substrate; it should not be interchanged with DX51D+Z without checking coating adhesion and forming behaviour.
Coating Mass, Finish and Tolerances
| Coating class | Zinc mass, both surfaces | Typical application |
|---|---|---|
| Z100 | 100 g/m2 | Indoor parts, painted components |
| Z140–Z180 | 140–180 g/m2 | General fabrication, appliances |
| Z275 | 275 g/m2 | Outdoor and architectural use, exposed profiles |
Sheet and coil for exposed architectural work is usually ordered zero spangle with a light skin pass, because the uniform surface accepts paint and prints evenly and avoids a visible pattern after forming. Regular spangle material is common for structural profiles, ducting and parts that will be painted with a heavy film or left unfinished.
Forming, Welding and Storage Notes
Forming: the coating deforms with the steel, so severe bending requires a formable grade such as DX52D or DX53D and an adequate bend radius; cracks in the coating usually indicate that the radius is too tight for the grade.
Welding: resistance spot welding is standard in appliance and automotive work but needs fume extraction. Arc welding should be done after removing the coating near the joint, and the affected zone should be re-protected afterwards.
Cutting: shearing and laser cutting leave a thin unprotected edge. Where edge corrosion matters, the cut edges are treated or the part is made from a heavier coating class.
Storage: keep coils and sheets dry, off the ground and under cover, with ventilation between sheets. Condensation trapped in a stack produces white rust, which is a cosmetic issue at first but reduces coating thickness if it continues.
Frequently Asked Questions
Q: Does zero spangle resist corrosion better than regular spangle?
No. Corrosion life depends on coating mass, coating adhesion and the environment. Zero spangle is specified for a uniform appearance and better paint response, not for longer service life.
Q: What is DX51D equivalent to in other standards?
In the JIS system SGCC is the closest general equivalent, and in ASTM A653 the commercial steel classes serve a comparable purpose. Strength level, chemistry limits and coating designations differ between the standards, so equivalence must be confirmed against the actual specification.
Q: What is the difference between DX51D and DX52D?
Both are hot-dip galvanized forming grades. DX52D has higher elongation and better drawability than DX51D, which makes it suitable for deeper pressings but slightly softer in the finished part.
Q: Is DX51D the same as DC51D?
No. DC51D+Z is defined on a DC01 cold-rolled substrate, while DX51D+Z may use a cold-rolled DC01 base or a hot-rolled DD11 base depending on the mill route. Substituting one for the other without review can change formability and coating adhesion.
Q: Which coating class should be chosen for an outdoor application?
Match the coating class to the corrosivity of the site and the expected service life. Z275 is the usual starting point for exposed outdoor profiles, while Z100 to Z180 is adequate indoors or under a protective paint system.
Q: Can galvanized coil be painted directly?
Yes, provided the surface treatment is compatible. A chromate-free passivated or lightly oiled surface is normally specified for painting, and the pretreatment line should be qualified for the coating in use.

