Why Surface Quality Matters for Roofing Coils
Roofing sheet is one of the most visible applications of DX51D+Z galvanized coil: it is roll-formed, cut, stacked and installed in large areas where every defect repeats across hundreds of metres of cladding. Surface quality therefore has a direct commercial value, and the three defects that generate most complaints are friction black spots, orange peel textures after stamping, and transverse bright stripes. Understanding their causes helps both the producer and the processor reduce scrap and settle acceptance questions on objective grounds rather than on appearance alone.
Friction Black Spots: Causes and Prevention
Friction black spots fall into two categories. In the narrow sense, they are caused by friction between coil laps during storage and transport: when coils are hoisted, stacked or shifted, relative movement between the laps rubs the zinc surface and produces dark, localised marks. In the broad sense, they can form during production, when interlayer friction inside the coil occurs during handling on the line, or during use, when parts are roughened by contact. Because the marks are mechanical, they are primarily a handling problem: coils should be stored on their sides on padded supports, lifted with soft slings or vacuum lifts, protected by edge protectors, and never allowed to rotate against each other. When spots appear, they are usually superficial, but if the rubbing has worn through the zinc layer, the area must be treated as an exposed-steel defect and repaired.
Orange Peel Defects During Stamping
The orange peel effect is the pebbly, rough texture that appears on the surface of a stamped or deeply formed part. It is not a coating defect; it is caused by the deformation behaviour of the substrate. The texture develops when the steel's grains deform unevenly, which is related to the dissolved carbon atoms in the substrate and to the production parameters: the hot rolling coiling temperature, the galvanizing soaking temperature and the finishing elongation all influence the final grain condition. Improper control of these factors leaves the steel with a structure that roughens visibly when it is stretched, producing the orange peel-like surface after stamping.
How to Improve the Orange Peel Defect
Improvement starts in the steelmaking and rolling process: reduce the dissolved carbon and nitrogen content in the substrate, precisely control the hot rolling coiling temperature and the galvanizing soaking temperature, and stabilize the finishing elongation at the temper mill so that the yield point behaviour of the strip is uniform. For the processor, the practical countermeasures are to reduce the degree of stretching where the design allows it, and to raise the forming severity step by step while inspecting the surface. If orange peel still appears, the coil should be tested with the actual stamping die before mass production, and the supplier should be asked for the coil's processing history.
Transverse Bright Stripes
Transverse bright stripes run across the width of the coil and are most commonly caused by the passivation solution coating roller. If the upper and lower surfaces are treated separately during coating, uneven pressure or roller wear easily leads to single-sided horizontal stripes, where bands of the surface have a slightly different appearance because the passivation film thickness varies. A useful field test: if the stripes are raised, they disappear after polishing, which confirms that they are only a passivation film variation and not a substrate or zinc layer defect.
Can a Coil with Bright Stripes Still Be Used?
If the stripes are caused only by uneven passivation solution coating and do not affect corrosion resistance, the striped side can be used as the inner surface of the roofing panel, where it is not visible. If the inspection shows exposed steel or damage to the zinc layer, the coil needs further evaluation, because a coating discontinuity at a stripe location will corrode earlier than the surrounding area. In every case, the decision should be based on the corrosion performance of the affected area, verified by coating thickness measurement, rather than on appearance alone.
Acceptance and Inspection Guide for Roofing Coils
1. Inspect the coil at receipt before decoiling: check the packaging, the edges and the first laps for damage and blackening. 2. During decoiling, examine a sample of the strip for spots, stripes and scratches under good lighting. 3. Measure the zinc coating mass with a magnetic gauge on both faces and compare it with the ordered class. 4. If defects are found, document them with photos and the coil number, and agree the disposition with the supplier: acceptance with discount, repair, or rejection. 5. Keep a sample of the defective strip for laboratory comparison if a claim is filed.
Frequently Asked Questions
Do friction black spots affect corrosion resistance?
Only if the rubbing has worn through the zinc layer. Superficial spots are a cosmetic issue; worn-through areas expose the steel and must be repaired with a zinc-rich paint.
Why does the orange peel texture appear only after stamping?
Because the texture is a deformation phenomenon: the substrate grains roughen when the steel is stretched, so the defect becomes visible only at the moment of forming, not on the flat coil.
Can orange peel be removed by polishing?
Polishing improves the appearance of the coating surface but does not fix the substrate condition; the texture will reappear on the next stamped part from the same coil, so process control is the only real cure.
Are transverse bright stripes a sign of missing zinc?
Usually not. The stripes come from uneven passivation film thickness; the zinc layer below is intact. A coating thickness measurement and the polishing test confirm the cause.
What should be written into the coil specification to protect the buyer?
The specification should state the acceptable defect limits, the inspection method, the coating mass class and the mill certificate requirements, so that surface claims are settled against measurable criteria.

