SPCC, SPCD and SPCE are the three commercial grades of cold-reduced carbon steel sheet and strip defined in JIS G 3141. They are not three different alloys but three levels of forming capability applied to a very similar low-carbon base material, which is why the same cold-rolled coil is often quoted against any of the three depending on how severe the forming operation is. Getting the level right avoids the two most common purchasing errors: paying for a fully deep-drawing grade where a simple bent bracket is required, and specifying a commercial grade for a part that must survive a deep draw without tearing.
What the SPCC, SPCD and SPCE Designations Mean
In the JIS G 3141 designation system, S stands for steel, P for plate and C for cold reduced. The fourth letter identifies the forming level: C for commercial quality, D for drawing quality and E for deep-drawing quality. Mill certificates frequently add a fifth character to describe the surface finish or the supply form, so SPCC-SD indicates a matt finish and SPCC-SB a bright finish.
SPCC – commercial quality. Intended for bending, roll forming and light stamping where bend radii are generous.
SPCD – drawing quality. Enough ductility for moderate drawing and stretching operations.
SPCE – deep-drawing quality. The highest forming level of the three, used where the draw is severe or the panel geometry is complex.
Grade-by-Grade Comparison
| Grade | Forming level (JIS G 3141) | Minimum tensile strength | Typical forming operations | Typical parts |
|---|---|---|---|---|
| SPCC | Commercial quality | 270 MPa | Bending, roll forming, shallow stamping | Enclosures, brackets, ducting, trim |
| SPCD | Drawing quality | 270 MPa | Moderate drawing and stretching | Appliance panels, cans, furniture frames |
| SPCE | Deep-drawing quality | 270 MPa | Severe deep drawing, complex panels | Automotive inner panels, housings, sinks |
JIS G 3141 sets a minimum tensile strength of 270 MPa for these cold-reduced grades. The real difference between SPCC, SPCD and SPCE is the elongation and forming requirement, which becomes progressively more demanding from SPCC to SPCE and is tabulated in the standard as a function of thickness rather than as a single universal value. That is why elongation figures quoted by different mills for the same grade can differ: they refer to different thickness ranges and to different testing directions.
Equivalent Grades in Other Standards
Because the designations describe formability rather than chemistry, they are normally cross-referenced to the European EN 10130 family rather than to a unique alloy number. The mapping below reflects how the grades are used in trade practice; it is an application-level equivalence, not a statement that the two specifications are identical in every limit.
| JIS G 3141 | EN 10130 | Chinese reference | Forming level |
|---|---|---|---|
| SPCC | DC01 | Q195 commercial cold-rolled sheet (GB/T 11253) | Commercial |
| SPCD | DC03 | Commercial drawing sheet | Drawing |
| SPCE | DC04 | Commercial deep-drawing sheet | Deep drawing |
For the American market the comparable specification is ASTM A1008/A1008M for cold-rolled carbon steel sheet. Older drawings that still call up ASTM A366 are referencing a withdrawn commercial-quality designation and should be updated to A1008/A1008M at the next revision.
Mechanical Properties and Formability
Strength: 270 MPa minimum tensile strength for SPCC, SPCD and SPCE under JIS G 3141.
Elongation: increases with forming level; the standard gives thickness-dependent minima, so always quote the target thickness when asking for a guaranteed elongation.
Surface: bright or matt finish, both compatible with painting, lacquering and subsequent zinc coating.
Supply sizes: cold-rolled sheet of this family is commonly supplied from about 0.15 mm to 3.0 mm thick and 600 mm to 1500 mm wide, in coil, cut sheet or slit strip.
Formability: the practical limit is the strain the material can accept at the die radius. SPCC tolerates generous radii, SPCD tolerates moderate draws, and SPCE is the correct choice when the part is deep, narrow or geometrically complex.
Typical Applications and Grade Selection
SPCC is the workhorse grade for the general sheet-metal shop: electrical enclosures, cable trays, ventilation ducting, shelving, brackets, sign frames and light structural covers. It is also the base material for many downstream coated products, because a commercial-quality cold-rolled substrate can be hot-dip galvanized, electrolytically zinc coated, painted or laminated.
SPCD is chosen when the part is produced by a drawing or stretching operation but the draw depth is moderate: washing machine and refrigerator side panels, furniture frames, can bodies, chassis components for small appliances and general hardware. SPCE is reserved for parts that push the material close to its forming limit, such as automotive inner panels, oil pans, seat frames, kitchen sink bowls, deep housings and complex domestic appliance pressings.
Whichever grade is selected, four practical points decide whether the material performs as intended in production.
Match the grade to the die, not to the drawing. Ask the tooling engineer for the drawing ratio or the maximum strain at the tightest radius, then choose the lowest grade that clears it with margin.
Specify dimensions, finish and tolerance. Thickness, width, edge condition, surface finish and flatness all affect press performance and downstream coating quality.
Inspect on receipt. Check thickness profile, camber, surface defects and oiling; a damaged surface cannot be corrected downstream.
Store dry and away from corrosives. Cold-rolled sheet has no protective coating, so it should be kept under cover, off the floor and away from acids, alkalis and salt-bearing atmospheres.
Handle the forming process. Lubricant choice, die clearance and blank orientation all change the achievable draw depth for a given grade.
Frequently Asked Questions
Q: Is SPCC the same as SPCD or SPCE?
No. All three come from JIS G 3141 with a 270 MPa minimum tensile strength, but SPCC is commercial quality, SPCD is drawing quality and SPCE is deep-drawing quality. They differ in the elongation and forming requirement, not in base chemistry.
Q: Which EN 10130 grade is equivalent to SPCE?
SPCE is normally treated as equivalent to DC04 in EN 10130 for deep-drawing applications. The comparison is application-level, so mechanical limits should be confirmed against the applicable standard when a certificate must be checked.
Q: Can cold-rolled SPCC be galvanized later?
Yes. Commercial-quality cold-rolled sheet is a common substrate for hot-dip galvanizing, electrolytic zinc coating and organic coil coating, provided the surface is clean and the forming and cleaning steps are controlled.
Q: What thickness is normally available?
This grade family is commonly supplied from about 0.15 mm to 3.0 mm, with widths typically between 600 mm and 1500 mm. Exact availability depends on the mill and on whether the order is for coil, sheet or slit strip.
Q: Why do two mills quote different elongation for the same grade?
Because JIS G 3141 specifies elongation minima against thickness ranges and test direction. Two suppliers may be quoting different thickness bands, so the thickness must be fixed before elongation figures can be compared.
Q: How should the grade be chosen for a new part?
Start from the forming severity. Generous radii and simple bends point to SPCC; a moderate draw points to SPCD; a severe or complex draw points to SPCE. Then confirm the choice with a trial pressing before releasing the specification.

