ST12, SPCC, DC01 and SGCC appear together on countless order sheets for flat steel, and buyers often treat the four names as interchangeable. They are not. The first three describe the same uncoated cold rolled steel under three different standards, while SGCC describes a hot dip zinc coated sheet in which that cold rolled steel is the substrate. Understanding which of the four an application actually needs prevents both overspending and premature corrosion failures.
ST12, SPCC and DC01: Three Names for Cold Rolled Sheet
Cold rolled flat steel of the DC01 type is one of the most widely used materials in the industrial sector, chosen for cold forming processes because of its combination of softness, clean surface and consistent thickness. The decisive standards for the quality and requirements of this material are DIN EN 10130 for cold reduced flat products and DIN EN 10152 for electrolytically zinc coated cold reduced flat products.
The grade carries several names. DC01 is the current European designation with the material number 1.0330, and it was known before as ST12 under the withdrawn German standard DIN 1623 and as FeP01 in older German usage. In Japan the same commercial quality cold rolled sheet is standardised in JIS G3141 as SPCC, and in China as DC01 in GB/T 5213. A mill certificate for DC01, an inspection certificate for ST12 and a JIS G3141 certificate for SPCC can therefore all describe the same coil.
DC01: EN 10130 basic grade of the DC steel family, material number 1.0330, former designations St12 and FeP01
ST12: designation in the withdrawn DIN 1623, now replaced by DC01
SPCC: JIS G3141 commercial quality cold rolled steel sheet and coil
SGCC: JIS G3302 hot dip zinc coated steel sheet, commercial quality
What DC01 and Its Neighbours Can Do
DC01 is intended for simple forming work such as bending, embossing, beading and drawing. Where the forming requirement rises to deep drawing and difficult profiling, DC03 is the grade to specify; it is a low carbon steel with excellent cold formability and a chemistry defined to deliver the required mechanical properties in the formed part. DC04 goes further again, with deep drawing properties that hold up under all types of deformation and suit high forming requirements.
The chemistry behind these grades is deliberately lean. Carbon, manganese, phosphorus and sulphur are held low, and aluminium is added to combine the nitrogen so that the sheet does not age and lose ductility in storage.
| Grade | C max % | Mn max % | P max % | S max % | Alt min % |
|---|---|---|---|---|---|
| DC01, formerly St12 | 0.10 | 0.50 | 0.035 | 0.025 | 0.020 |
| DC03, formerly St13 | 0.08 | 0.45 | 0.030 | 0.025 | 0.020 |
| DC04, formerly St14 and St15 | 0.08 | 0.40 | 0.025 | 0.020 | 0.020 |
DC01 steel is ferritic and therefore magnetic. This matters in electrical equipment, where DC01 is used in applications that need formability, strength and magnetic properties at the same time, such as the production of electrical enclosures and internal components.
SGCC: The Zinc Coated Member of the Group
SGCC is not a cold rolled grade in the same sense as the others. It is a commercial quality hot dip galvanized steel sheet defined in JIS G3302, produced by passing cold rolled substrate through a molten zinc bath so that a metallurgically bonded zinc coating forms on both surfaces. The coating protects the steel by barrier action and, at cut edges and scratches, by sacrificial action, which is why SGCC sheet is used for roofing, ducting, cable trays, air conditioning housings, appliance backs and other parts exposed to weather or condensation.
Coating mass is the key ordering parameter. Under JIS G3302 the coating is designated by numbers such as Z08, Z12, Z18 and Z27, and under EN 10346 by designations such as Z100, Z140, Z200 and Z275, where the number expresses the total zinc mass in grams per square metre on both surfaces. A higher coating mass means longer service life in a given environment, but it also affects formability at tight bend radii, because a heavy coating can flake if the bend is too sharp. Surface condition is ordered as normal spangle, minimised spangle or skin passed, and the choice determines whether the sheet will be painted or left bare.
Choosing Between DC01 Grade Cold Rolled Sheet and SGCC
Use ST12, DC01 or SPCC sheet when the part is painted, powder coated or used indoors and the environment is dry
Use SGCC galvanized sheet when the part sees humidity, condensation, rain or an outdoor atmosphere
Use a drawing grade such as DC03, DC04 or SPCE when the part is deep drawn, regardless of the coating choice
Use electrolytically zinc coated material to DIN EN 10152 when a thin, smooth, easily painted coating is required rather than the heavier hot dip layer
A practical rule is to select the forming grade first and the coating second. If a part must be deep drawn and also corrosion resistant, the drawing grade is chosen for the substrate and the coating route, hot dip galvanized or electrogalvanized, is selected afterwards on the basis of the environment and the paint system.
Coil, Sheet and Processing Options
All four designations are supplied as coil, slit strip, cut to length sheet and blanks. Common thicknesses run from 0.3 mm to 3.0 mm and widths from 600 mm to 1500 mm. Cold rolled material is lightly oiled for transport; galvanized material is normally supplied either oiled or with a chromate free passivation, and the two must not be confused when the sheet is to be painted, because a passivation film that protects the zinc during storage can interfere with paint adhesion if it is not specified correctly. Slitting, cut to length, shearing, bending and profiling are standard processing steps, and coil weight, inner diameter and edge condition are agreed per order.
Frequently Asked Questions
Q: What is DC01 steel material?
DC01 is a cold rolled flat steel widely used in industry for cold forming because of its good properties. Its quality requirements are governed by DIN EN 10130 for uncoated material and by DIN EN 10152 for the electrolytically zinc coated version.
Q: What is the difference between DC01 and DC03 steel?
DC01 is used for simple forming work such as bending, embossing, beading and drawing, while DC03 suits forming requirements such as deep drawing and difficult profiling because it has lower carbon and better elongation.
Q: What is the DC01 steel number?
DC01 is material number 1.0330. It is the basic grade of the DC steel family and was previously designated St12 or FeP01.
Q: Is SGCC the same as DC01 or SPCC?
No. SGCC is a hot dip zinc coated sheet to JIS G3302, while DC01 and SPCC are uncoated cold rolled grades. SGCC uses cold rolled steel as its substrate, so the two groups are related but not interchangeable.
Q: Which grade should be ordered for a deep drawn, corrosion resistant part?
Specify a drawing grade such as DC03, DC04 or SPCE for the substrate, then choose a zinc coating route. Deep drawing and coating mass must be balanced, since very heavy coatings are less tolerant of tight bend radii.
Q: Are these steels magnetic?
Yes. DC01, DC03, DC04, SPCC and the SGCC substrate are ferritic low carbon steels and are magnetic, which is useful in electrical enclosures and components.

