What Factors Affect the Corrosion Resistance of Cold-Rolled Galvanized Steel

Sep 08, 2025 Leave a message

Plain Zinc, Zinc Alloy and Zinc-Aluminium-Magnesium Coatings

Cold-rolled galvanized sheet is judged first on the type of coating it carries, because coating chemistry decides the corrosion mechanism itself. A plain zinc coating protects steel through sacrificial action: zinc is more active than iron, so it corrodes preferentially and keeps the steel sound while the coating lasts. Its weakness is that the white-rust film of zinc oxide and zinc hydroxide is loose and easily washed away, so long-term performance in wet atmospheres is only moderate.

Coating type Protection mechanism Surface hardness Best-fit service
Plain zinc Sacrificial anode with a loose hydroxide film Low to moderate Indoor parts, general forming, painted substrates
Zinc-iron alloy Dense alloy barrier with limited sacrificial action High Welded and painted automotive-type parts
Zinc-aluminium-magnesium Compact passivating film plus self-healing at scratches Moderate to high Roofing, cladding, coastal and agricultural structures

Zinc-aluminium-magnesium coatings form a compact magnesium-aluminium passivating layer that resists both acid and alkaline attack, and magnesium released at a scratch promotes a new protective film. On comparable coating masses this family typically delivers several times the atmospheric durability of plain zinc, which is why it dominates modern architectural coil.

Coating Thickness: The Protective Reserve

Thickness sets how much zinc is available to be consumed. In a neutral outdoor atmosphere a 120 g/m2 double-sided pure zinc coating corresponds to a service life of roughly 10 to 15 years, while a 275 g/m2 coating extends the same structure to about 20 to 25 years. The relationship is broadly linear in the same environment, which makes coating mass the practical lever for matching a build to its expected service period.

The relationship is not without limits. Above roughly 350 g/m2 plain zinc loses ductility and tends to crack during bending, and the added cost begins to exceed the marginal corrosion benefit. For heavily formed parts a thinner but more ductile or alloy-based coating usually outperforms a heavy plain zinc coating that fractures on the press brake.

Coating Uniformity, Pinholes and Adhesion

Average coating mass can hide dangerous local weakness. Incomplete cleaning before immersion leaves skip spots and pinholes that expose steel directly, and each such defect becomes a small anode facing a large zinc cathode, so corrosion digs in rather than spreading sideways. The result is pitting that penetrates the sheet long before the average coating is exhausted.

Skip plating and pinholes are traced back to pretreatment rather than to the zinc bath, and are removed by verified degreasing and pickling.

Adhesion verification by bend, cupping or tape test is the routine acceptance check on cold-rolled galvanized coil.

Substrate Surface Condition Before Coating

Because cold-rolled substrate is coated in a continuous line, any residue on the surface is sealed into the finished product. Residual rolling oil left by incomplete degreasing forms a film that blocks wetting by the zinc and produces local coverage gaps. Incomplete pickling leaves iron oxide that reacts with the zinc bath to build a brittle alloy layer, cutting coating ductility and causing cracks along bends.

Surface roughness needs to sit in a narrow window. A very smooth substrate below roughly Ra 0.5 micrometre offers too little mechanical key and the coating peels; a very rough substrate above roughly Ra 5 micrometres produces uneven coating, thin in the valleys and thick on the peaks, and the thin valleys corrode first.

How the Corrosive Medium Decides Everything Else

The environment determines which corrosion mechanism is active, and therefore which coating property matters.

Neutral outdoor exposure consumes zinc slowly through electrochemical oxidation, on the order of a few grams per square metre per year.

Acidic media attack both the metal and its hydroxide film, multiplying the consumption rate several times over.

Alkaline media dissolve zinc as soluble zincate and keep attacking as long as the surface remains wet.

Salt spray, marine air and de-icing salt are the most severe common case: chloride penetrates the film, builds a conductive electrolyte layer and drives pitting, with annual losses an order of magnitude above the neutral case.

Frequently Asked Questions

Q: Why is zinc-aluminium-magnesium coating more corrosion resistant than plain zinc?
It builds a compact passivating film instead of a loose hydroxide layer, and magnesium released at a scratch re-forms that film to protect the exposed area.

Q: At what coating mass does thicker stop helping?
Plain zinc above roughly 350 g/m2 becomes noticeably less formable, so the extra corrosion reserve is partly lost to cracking on formed parts.

Q: What causes pitting on an otherwise fully coated sheet?
Skip plating and sub-millimetre pinholes from insufficient pretreatment. They expose the substrate and act as small anodes, so attack goes into the thickness instead of spreading.

Q: How does substrate roughness influence coating quality?
Too smooth and the coating cannot key mechanically, too rough and the coating is uneven, with thin valleys that rust first.

Q: Which environment consumes a zinc coating fastest?
Chloride-rich service, such as marine air, salt spray or road de-icing salt, because chloride drives pitting on top of the normal zinc consumption.