1.What challenges does the zinc coating present?
Zinc fumes and health hazards: Zinc has a boiling point of approximately 907°C, far lower than the melting point of steel (approximately 1500°C). During welding, the zinc layer evaporates, producing a large amount of white zinc fumes. Inhalation of these fumes can cause "metal fume fever," leading to flu-like symptoms such as fever, cough, and fatigue.
Porosity: If the evaporated zinc vapor is trapped in the molten pool and cannot escape, it will form porosity inside the weld, severely weakening the weld's strength and density.
Cracks: Zinc penetrates the grain boundaries of the weld metal, forming brittle phases and increasing the weld's susceptibility to hot cracking (especially solidification cracking).
Inclusions and lack of fusion: Residual zinc oxide (zinc oxide) can form inclusions and affect arc stability, leading to poor fusion.

2.What are the advantages of alkaline, low-hydrogen welding electrodes?
Excellent zinc removal ability: The coating of basic welding electrodes contains a large amount of marble, fluorite, etc., which can generate a strongly reducing welding atmosphere, helping to decompose and remove zinc oxides.
Low hydrogen content: Effectively prevents delayed cracking (cold cracking) caused by hydrogen, resulting in good plasticity and toughness of the weld metal.
High weld quality: Excellent mechanical properties, especially impact toughness, suitable for structures subjected to dynamic loads.
Note: This type of welding electrode requires slightly higher welding skills, necessitates short arc operation, and the electrode must be strictly dried before welding (usually baked at 350-400°C for 1 hour).

3.What are the reasons and disadvantages of using titanium-calcium type welding electrodes?
Reasons:
Good processability: Stable arc, minimal spatter, easy slag removal, and aesthetically pleasing weld formation, making it ideal for beginners.
Wide applicability: J422 is a perfectly viable choice for ordinary structures, non-load-bearing components, or thin plates that do not require extremely high mechanical properties.
Disadvantages: Compared to J507, its zinc removal ability and resistance to porosity are slightly weaker, and the weld's plasticity and toughness are also lower.

4.What are the key welding process techniques?
Pre-welding cleaning (most important!):
Best method: Grind or mill off as much zinc as possible from the weld bevel and within a 20-30mm radius on both sides. This is the most effective way to avoid zinc problems.
If cleaning is not possible: Then it must be compensated for through the welding process.
Increase welding current:
Compared to welding ordinary steel plates of the same thickness, the current should be increased by 10%-20%. This helps zinc evaporate and escape more quickly, preventing the molten pool from solidifying too quickly and trapping it.
Increase welding speed & control the arc:
Do not stay in one place for too long. Use a faster welding speed to allow sufficient time for the zinc in front of the molten pool to evaporate, rather than being drawn into the molten pool.
Appropriately lengthen the arc to allow more channels for zinc vapor to escape (but be careful not to make it too long, which would result in poor shielding).
Increased Bevel Angle:
Compared to unzinc-coated steel plates, the bevel angle should be appropriately increased (e.g., from 60° to 70°~80°) to provide a wider path for zinc vapor to escape.
Forced Ventilation and Personal Protective Equipment:
Work must be done in a well-ventilated area, preferably using localized fume extraction equipment to remove zinc fumes at the source.
Welders must wear qualified dust masks or supplied-air face shields; ordinary masks must never be used.
5.What are the summary and selection recommendations?
J507 (E5015): Advantages: Good weld mechanical properties, strong crack resistance, and strong zinc removal ability; Disadvantages: High operational requirements, requires a DC welding machine, and the welding rods need to be dried.
J506 (E5016): Advantages: Can be used with AC welding machines; Disadvantages: Requires high operational skills, welding rods need to be dried.

