Hot-dip galvanized coil is oiled because zinc is a reactive metal that corrodes in ordinary air. The oil film is a low-cost physical barrier that keeps moisture, oxygen and airborne contaminants away from the zinc surface during storage, handling, transport and the early stages of forming. For coils that may sit in a warehouse or cross an ocean before they are used, that barrier is the difference between a bright, workable surface and one covered in white rust.
How White Rust Forms on Zinc
The zinc layer protects the steel by acting as a sacrificial anode, but that same reactivity means the zinc itself reacts with water, oxygen and carbon dioxide to form zinc hydroxide and basic zinc carbonate, plus zinc hydroxychloride in chloride-bearing environments such as coastal air. These products are loosely adhering, white to grey, and offer no protection at all. The corrosion rate depends strongly on the local environment, and the atmospheric corrosivity categories of ISO 9223 are the usual way of describing that exposure. The worst case is not rain but condensation: when a coil cools overnight and drops below the dew point, moisture condenses between the wraps where it cannot evaporate, and that trapped film is what produces white rust in storage.
The Oil Film as a Barrier
An oil film applied on the galvanizing line interrupts the corrosion cycle before it starts. Water cannot reach the zinc, oxygen cannot dissolve into it, and the thin electrolyte layer needed for electrochemical attack never forms. Applied as a continuous, uniformly thin film over the full coil width, oiling is one of the most cost-effective forms of temporary protection available for galvanized coil. It is a complement to, not a replacement for, adequate coating mass: a heavier zinc coating to EN 10346 or ASTM A653/A653M extends the time the coil can tolerate exposure, while the oil film controls the condition of the surface during that time.
Lubrication During Forming and Protection in Storage
The second function of the oil is tribological. Zinc is soft, and where a coated sheet rubs against a die or forming roll the zinc can pick up and transfer to the tool, a failure mode known as zinc pick-up or galling. Once that starts, friction rises, scratches appear on the sheet and the tool surface degrades. An oil film reduces the direct metal-to-metal contact between coating and tool, keeps the zinc where it belongs, limits scoring on the visible surface and extends die life. Forming oils with higher lubricity go further, lowering the stress concentrations that cause tearing in deep drawn parts such as appliance linings and enclosure panels.
Warehouse storage: temperature swings in humid regions cause condensation on the coil surface, and airborne dust and contaminants settle on the outer wraps. The oil film isolates the zinc from both.
Coil stacking: layers press against each other and vibrate during handling. Oil buffers that contact and prevents fretting wear from exposing bare steel.
Sea freight: salt-laden air and high humidity create the chloride-rich conditions that produce zinc hydroxychloride. Oiling, combined with proper wrapping and desiccant, controls the risk.
Edge protection: coil edges are the thinnest part of the coating and the first place to suffer. Uniform edge-to-edge oiling covers them.
Matching the Oil to the Application
Not every coil needs the same amount of oil, and applying more than the next process can tolerate creates its own problems. The film weight is normally chosen from the end use and the expected storage period, and is checked on the line by film thickness measurement to ensure there are no uncoated areas.
| Oiling level | Indicative film weight per side | Suited to |
|---|---|---|
| Light | About 0.5-1.0 g/m2 | Parts to be painted or laminated, building panels |
| Medium | About 1.0-2.0 g/m2 | General stamping and bending |
| Heavy | About 2.0-3.0 g/m2 and above | Long storage, overseas export, stock held beyond several months |
| Forming oil | Selected by forming severity | Deep drawing and complex shapes such as automotive and precision hardware parts |
Application Control and Removal Before Painting
Two disciplines keep oiling from becoming a defect source. The first is uniformity: a worn or unevenly loaded oiling roller leaves uncoated strips that rust while the rest of the coil stays clean, so the film is monitored on line and the applicator is maintained regularly. The second is removability. Oil is not a permanent coating, and any downstream process that needs paint or adhesive to bond, such as composite panel production, requires the film to come off first. Alkaline cleaning or spray degreasing is the standard step, so the oil grade should be chosen for easy removal and low residue, and the paint system and the oil should be reviewed together rather than independently.
FAQ
Q: Why does galvanized coil develop white rust in storage?
Trapped moisture between the coil wraps forms a thin electrolyte film on the zinc surface, which reacts with oxygen and carbon dioxide to give loose white zinc hydroxide and zinc carbonate. Oiling prevents the electrolyte film from forming.
Q: Is oiling necessary if the zinc coating is heavy?
A heavier coating mass to EN 10346 or ASTM A653/A653M extends the exposure the coil can tolerate, but it does not stop condensation between wraps. Oiling controls the surface condition during storage and transport.
Q: Does the oil need to be removed before painting?
Yes. Paint and adhesive need a clean surface, so alkaline cleaning or spray degreasing is required. Choose an oil that is easily removed and leaves minimal residue.
Q: How much oil is normally applied?
It depends on the end use and storage time: roughly 0.5-1.0 g/m2 per side for light protection, 1.0-2.0 g/m2 for general forming, and 2.0-3.0 g/m2 or more for long storage and export.
Q: Can oiling replace a passivation treatment?
No. The two address different risks. Passivation stabilises the zinc surface chemically, while oiling provides the physical moisture barrier and forming lubrication.
Q: What causes bare patches in the oil film?
Wear or uneven loading of the oiling roller, or an incorrect setting of the applicator, leaves areas uncoated. On-line film thickness checks and routine roller maintenance prevent this.

