Q235 Galvanized Coil: Density, Hardness and Performance Limits

Jan 20, 2026 Leave a message

Q235 is the most widely used structural carbon steel in China, defined in GB/T 700, and it is also one of the most common substrates for hot-dip galvanized coil sold on the export market. Buyers frequently ask about its density, hardness, corrosion resistance and temperature limits before specifying a galvanized product. This article answers those questions with reference to the standard properties of Q235 and explains how it relates to the DX51D designation used for galvanized coil under EN 10346.

Density of Q235

The density of Q235 is 7.85 g/cm3, identical to that of ordinary carbon steel. This value is used in weight calculations for shipping, structural design and pricing: a 1 mm thick, 1250 mm wide coil weighs about 9.8 kg per running metre. The zinc coating adds only a small amount of mass, typically 100-275 g/m2 for galvanized products, which is negligible for most structural calculations.

Hardness and Machinability

In the untreated condition, the Brinell hardness of Q235 is approximately HB 120-150. This relatively low hardness gives the steel good machinability: it can be cut, punched, bent and welded without special tooling, which is why it is preferred for frames, supports, enclosures and general fabrication. After hot-dip galvanizing the hardness of the steel base is essentially unchanged, while the zinc-iron intermetallic layers of the coating add surface wear resistance.

Corrosion Resistance of Q235

Q235 has poor natural corrosion resistance. Without protection it rusts readily in humid environments because its surface oxide film is not self-healing. The standard protective measures are painting, oiling or galvanizing. Hot-dip galvanizing provides both a barrier layer and sacrificial cathodic protection: even where the coating is scratched down to the steel, the surrounding zinc corrodes preferentially and shields the exposed area. Coating masses of Z100 to Z275 g/m2 per EN 10346 are common for outdoor Q235 galvanized coil.

Temperature Performance of Q235

Q235 can be used stably at service temperatures below 200 C. Above 300 C its strength decreases significantly, so it is not suitable for high-temperature applications such as boiler parts or flue components. Low-temperature behaviour depends on the quality grade: grade A has poor low-temperature toughness and can become brittle in cold service, while grade D offers good toughness and can be used at temperatures down to about -20 C. For cold-climate structures, specify grade D or a killed steel with controlled impact properties.

Q235 and the DX51D Designation

On the international market, galvanized coil made from Q235-type low-carbon steel is commonly traded under the European designation DX51D+Z defined in EN 10346. In the designation, DX means steel for cold forming, 51 is the forming class, D indicates the product form of strip and sheet, and Z denotes a pure zinc coating. DX51D+Z is the general-purpose bending and forming grade, with maximum carbon content of 0.18%, tensile strength range of 270-500 MPa and minimum elongation of 22%. The equivalent Japanese designation is SGCC under JIS G3302, and the Chinese counterpart in GB/T 2518 follows the same Z coating notation.

Frequently Asked Questions

What is the density of Q235 steel?

7.85 g/cm3, the same as ordinary carbon steel. This value is used for weight and structural calculations.

What is the typical hardness of Q235?

In the untreated condition, the Brinell hardness is approximately HB 120-150, which gives the steel good machinability for cutting, punching, bending and welding.

Does Q235 rust easily?

Yes. Q235 has poor natural corrosion resistance and rusts readily in humid environments. It must be protected by painting, oiling or hot-dip galvanizing.

Can Q235 be used at high temperature?

It is stable below 200 C. Above 300 C its strength drops significantly, so it is not suitable for high-temperature service.

What is the low-temperature limit of Q235?

It depends on the grade. Grade A is brittle at low temperatures and unsuitable for cold service; grade D has good toughness and can be used down to about -20 C.

How does Q235 relate to DX51D+Z?

Galvanized coil made from Q235-type steel is commonly specified as DX51D+Z under EN 10346, with equivalents SGCC under JIS G3302 and the corresponding grades in GB/T 2518.