Common Uses of Galvanized Steel Pipe in Water, Drainage, Gas and Structure

Aug 21, 2025 Leave a message

Why Galvanized Pipe Is Still Specified

Galvanized steel pipe is a welded or seamless steel tube that has been coated with zinc, normally by the continuous hot-dip process, so that both the bore and the outside are protected. The combination is cheap, strong, easy to thread, easy to weld and resistant to the mixed wet and dry conditions found in buildings, which is why it remains in specification for services where a plastic pipe cannot provide the mechanical strength or the fire performance required.

The governing standards differ by market. Hot-dip galvanized welded steel pipe for low-pressure liquid delivery is standardised in GB/T 3091; black and hot-dipped zinc-coated welded and seamless pipe is covered by ASTM A53/A53M in Grades A and B; non-alloy steel tubes suitable for welding and threading are covered by EN 10255 in light, medium and heavy series; and the coating applied to tubes by hot-dip galvanizing is covered by EN 10240, with ISO 1461 giving the general coating thickness requirements for batch-galvanized products.

Water Supply and Distribution

Galvanized pipe was the standard material for building water services for most of the last century, and it is still used for outdoor municipal mains, community supply lines and site distribution where the water quality is not critical, such as irrigation mains, road sprinkler lines and construction supply. It is also used where a buried line must resist mechanical loads, since a steel wall recovers from ground movement that would deform a plastic pipe.

Inside buildings, the material is now specified less often for potable water because a zinc coating reacts with some waters and the corrosion products and any detached coating can affect water quality; internal potable distribution has largely moved to plastic-lined or non-metallic systems. Where galvanized pipe is retained for internal work, the normal practice is to keep water velocity and dissolved oxygen in a range that promotes a stable protective layer, and to avoid mixing galvanized and copper pipe in the same circuit without a dielectric break, because the resulting galvanic couple attacks the zinc.

Drainage, Rainwater and Ventilation

In drainage, the coating's tolerance of alternating wet and dry conditions makes galvanized pipe useful for external rainwater downpipes, roof drainage, yard gullies and community sewage branches where the effluent is not strongly acidic. It is also widely used for building downspouts, since the zinc coating resists rain and weathering far better than painted or bare steel and requires no repainting.

In ventilation, galvanized spiral and straight ducting is standard for general exhaust and supply systems, because the zinc coating limits rust inside ducts carrying humid air and gives an acceptable surface for general building services. For ductwork carrying chemically aggressive fumes or for food and pharmaceutical duty, a different material or an internal coating is needed, since zinc is attacked by acids and alkalis.

Service Typical size range Common specification route
Low-pressure water delivery DN15 to DN100 Hot-dip galvanized welded pipe to GB/T 3091
Rainwater and downpipes DN50 to DN150 Galvanized pipe sized to drainage calculation
Gas distribution and risers DN15 to DN50 Threaded galvanized pipe with sealed joints
Heating risers and exposed pipes DN15 to DN65 Galvanized pipe, insulation applied on site
Fire service piping DN25 to DN150 Galvanized pipe to the fire system specification
Scaffolding and structural tube 48.3 mm and 60.3 mm outside diameter Coated tube to the scaffold tube standard

Gas, Heating and Fire Services

Galvanized pipe has a long history in low-pressure gas distribution, including yard branches and indoor risers, where threaded joints with a suitable sealant give a sound and inspectable connection. In older districts the material is still in service and is preferred where a high-strength, impact-resistant line is required, such as an overhead yard main. In new work, gas distribution has largely moved to polyethylene for buried lines and to copper or steel for above-ground runs.

For heating, galvanized pipe continues to be used for exposed risers and radiator connections because it tolerates the temperature range of domestic hot water and is resistant to mechanical damage. The material suits closed heating circuits where the water chemistry is controlled; in an open circuit with high dissolved oxygen, zinc corrosion is faster and the resulting sludge can block valves and radiators, so the water treatment regime must be specified along with the pipe.

Fire services commonly use galvanized pipe for wet risers, hydrant pipework and sprinkler laterals, because the coating resists internal corrosion during the long idle periods typical of a fire main, and the steel wall gives the fire performance expected of the system. Where the circuit is wet and permanently pressurised, verify that the coating is compatible with the specific extinguishing medium and that the specified wall thickness satisfies the fire design.

Sizes, Coating and Threaded Joint Practice

Galvanized pipe is ordered by nominal size, with the outside diameter fixed by the dimensional series so that threads and fittings are interchangeable. In the EN 10255 series, the outside diameters run from 21.3 mm for DN15 through 26.9 mm for DN20 and 33.7 mm for DN25 to 60.3 mm for DN50 and 114.3 mm for DN100. In the ASME series the corresponding nominal pipe sizes have very similar but not identical outside diameters - for example 33.4 mm for NPS 1 against 33.7 mm for DN25 - so the dimensional standard must be stated, particularly for fittings and for existing systems.

Coating quality is decided during galvanizing: the tube must be clean, the bore must be drained, and the galvanizing must reach a thickness consistent with the applicable standard so the sacrificial protection lasts. Cut ends, threaded ends and welded joints all expose steel, so cut-back coating must be repaired with a zinc-rich material and threaded joints should be assembled with a sealant or tape that does not attack the coating.

Installation and Inspection Points

The details that decide whether a galvanized pipeline lasts are ordinary ones. Keep the pipe off the ground before installation and store it under cover with the ends capped, because a damp bore rusts from the inside. Support the line so that water cannot pond at low points. Isolate galvanized pipe from direct contact with copper, brass, stainless steel and bare carbon steel in wet conditions, or provide a dielectric break, because a galvanic couple will consume the zinc quickly. Do not use galvanized pipe for steam condensate or for fluids outside a moderate pH range without checking the exposure first.

On delivery, check the coating for thickness and continuity, look for uncoated patches in the bore on a sample tube, verify the outside diameter and wall thickness against the ordered standard, and confirm that the marking was applied consistently. Record the heat numbers and keep the certificates with the line identification, so that any later repair can be matched to the original material.

Frequently Asked Questions

Q: Are galvanized pipes still used for drinking water?
A: They remain in service in many older buildings and are still used for non-critical supply such as irrigation and construction water. For internal potable distribution, non-metallic or lined systems are now the normal choice because the coating can react with the water and affect quality.

Q: What standards govern galvanized steel pipe?
A: GB/T 3091 for hot-dip galvanized welded steel pipe for low-pressure liquid delivery, ASTM A53/A53M Grades A and B for welded and seamless zinc-coated pipe, EN 10255 for tubes suitable for welding and threading, and EN 10240 for the galvanized coating on tubes.

Q: Why are the outside diameters different for the same nominal size?
A: Different dimensional series use slightly different outside diameters - for example 33.4 mm for NPS 1 and 33.7 mm for DN25. Always state the dimensional standard, especially when matching existing fittings.

Q: Can galvanized and copper pipe be connected directly?
A: Not safely in a wet location. The galvanic couple attacks the zinc and the galvanized pipe corrodes quickly, so a dielectric union or a non-metallic transition piece must be used.

Q: How should cut ends and threads be treated?
A: Every cut and thread removes the coating and exposes bare steel. Repair the exposed area with a zinc-rich coating compatible with the original galvanizing, and use a sealant on threaded joints that does not chemically attack zinc.

Q: Is galvanized pipe suitable for high-temperature service?
A: It is commonly used for domestic hot water and heating risers with the water chemistry controlled. It is not suitable for steam condensate or for continuously high temperatures, where the coating is consumed rapidly.

Q: What should be inspected on delivery?
A: Coating thickness and continuity on a sample, absence of uncoated patches in the bore, outside diameter and wall thickness against the ordered standard, straightness and end condition, and consistent marking with heat numbers matching the certificates.