SGCC is one of the most widely traded galvanized sheet designations in Asia, and buyers ask the same question at every technical review: how strong is it, and what can it be used for? The strength of SGCC sheet comes from the cold-rolled steel substrate rather than from the zinc coating, and the standard defines a range that comfortably covers appliances, building panels and light structural work.
What the SGCC Designation Means
SGCC is a commercial-quality hot-dip zinc-coated steel sheet and strip grade defined in JIS G 3302. The letters denote steel, galvanized, commercial quality, and the product is supplied as coil, sheet or slit strip. The closest European and Chinese equivalents are DX51D under EN 10346 and the corresponding commercial galvanized grades of GB/T 2518, so a triple-standard technical agreement is common when a project sources from different regions.
Mechanical Strength of SGCC Sheet
Tensile strength of SGCC sheet falls in the range of 270 to 500 MPa, and yield strength is approximately 140 to 280 MPa, depending on the steel substrate supplied by the mill. Because the grade is commercial quality, the standard sets minimum values and the mill reports the actual figures on the inspection certificate.
| Property | Typical range for SGCC | Notes |
|---|---|---|
| Tensile strength | 270 to 500 MPa | Governed by the base steel, unaffected by coating |
| Yield strength | 140 to 280 MPa | Verified on the mill test report for each heat |
| Elongation | Specified by thickness class | The standard sets minimum elongation values that vary with gauge |
| Coating contribution to strength | Not counted in design | Zinc is a corrosion layer, not a structural layer |
| Structural alternatives | SGC340, SGC400, SGC440 | Higher minimum yield grades listed in the same standard |
Two practical consequences follow. First, structural calculations should use the base steel thickness, not the coated thickness, because design rules do not credit the zinc layer with load-carrying capacity. Second, where a project needs more than commercial-quality strength, the structural grades of the same standard offer higher minimum yield values and should be specified explicitly on the drawing.
Thickness, Coating Mass and Load Capacity
SGCC sheet is commonly supplied between about 0.2 mm and 2.0 mm thick, with coating designations such as Z100 to Z275 or the equivalent zinc-iron alloy coatings. The choice of coating mass is a corrosion decision, not a strength decision: a heavier coating extends service life in a harsh environment but adds only a few micrometres of thickness per side and is disregarded in the structural calculation.
Formability and Fabrication
Cold rolling gives SGCC sheet a smooth surface and uniform thickness, which is why it presses, bends, rolls and shears predictably on high-speed lines. Commercial quality is intended for simple forming. Where the part involves a deep draw, cracking of the zinc layer can occur, and the usual responses are to use a drawing or deep-drawing grade, to increase the bend radius, or to adjust tool clearance and lubricant.
Welding SGCC Sheet
Welding galvanized sheet is routine but needs attention to the coating. Zinc boils at a relatively low temperature, so arc welding produces zinc fume and spatter, and the coating is destroyed in the weld zone. Resistance spot welding is the standard process in appliance and automotive lines, while TIG or pulsed MIG welding gives cleaner beads on visible joints. After welding, clean the weld and heat-affected zone and protect them with a zinc-rich repair coating, because these areas have lost their sacrificial protection.
Painting and Surface Preparation
SGCC sheet takes paint readily once the surface is clean and free of oil, and a pre-treatment such as a conversion coating improves adhesion. Painting raises both corrosion resistance and appearance, which is why the grade is widely used for appliance housings, air-conditioning casings, switch cabinets and architectural panels that are finished after forming.
How SGCC Coil Is Produced
Cold rolling of hot-rolled pickled coil to the final gauge, which sets thickness tolerance and surface quality.
Cleaning, degreasing and pickling to remove oil, oxide and mill contamination.
Annealing to develop the required ductility and grain structure.
Continuous hot-dip galvanizing by passing the strip through molten zinc at approximately 450 to 460 °C.
Post-treatment: cooling, skin pass, tension levelling, straightening, trimming and slitting to the ordered width.
Frequently Asked Questions
Q: What is the tensile strength of SGCC sheet?
It normally falls between 270 and 500 MPa, with yield strength of roughly 140 to 280 MPa, and the exact values are reported on the mill certificate for each batch.
Q: Is SGCC sheet strong enough for structural use?
It is a commercial-quality grade intended for panels and general fabrication; load-bearing structures should use the higher yield structural grades of the same standard, such as SGC340 or SGC400.
Q: Does a heavier zinc coating make SGCC sheet stronger?
No. The coating improves corrosion resistance only, and design calculations are based on the base steel thickness.
Q: Can SGCC sheet be welded without damaging the coating?
The coating is always destroyed locally by welding heat, so the sound approach is to weld with a suitable process, then clean the joint and restore protection with a zinc-rich repair coating.
Q: Can SGCC sheet be deep drawn?
Commercial quality tolerates only simple forming; deep drawing is handled by drawing and deep-drawing grades, or by adjusting radius, clearance and lubrication on a case-by-case basis.
Q: Which standards cover SGCC sheet?
The grade itself is defined in JIS G 3302, with equivalent products available under EN 10346 and GB/T 2518 for projects that specify European or Chinese standards.

