Let's take a look at the production process for SGCC galvanized steel sheets.

Sep 10, 2025 Leave a message

Let's take a look at the production process for SGCC galvanized steel sheets.
SGCC is a general commercial hot-dip galvanized steel sheet defined in the Japanese JIS standard (JIS G3302). Its production process primarily utilizes the continuous hot-dip galvanizing method (the mainstream modern process). The core process involves immersing cold-rolled or hot-rolled steel sheets in molten zinc to form a uniform zinc layer on the surface. The specific process is as follows:
1. Raw Material Preparation: Substrate Selection
SGCC substrates are typically low-carbon steel sheets (such as cold-rolled SPCC or hot-rolled SPHC). The substrate surface must be clean and free of heavy scale or oil contamination, which can affect the adhesion of the zinc layer. The substrate thickness is adjusted based on the SGCC product requirements (generally 0.3-3.2mm).
2. Pretreatment: Removing surface impurities to ensure zinc layer adhesion.
Pretreatment is a critical step in galvanizing quality. Its purpose is to remove scale, oil contamination, and rust from the substrate surface, allowing for a uniform active layer to form on the steel sheet, facilitating zinc layer adhesion. Degreasing: Use alkaline cleaning (such as sodium hydroxide solution) or spray cleaning to remove rolling oil, oil stains, and other organic impurities from the steel plate surface to prevent subsequent rust removal and zinc coating adhesion.
Pickling: Soak or spray the steel plate with hydrochloric acid or sulfuric acid solution to dissolve surface oxide scale (Fe₂O₃, Fe₃O₄, etc.) and rust, revealing a clean iron substrate. After pickling, rinse with water to remove residual acid and prevent corrosion of the substrate.
Electrolytic Cleaning (Optional): For substrates with higher requirements, electrolysis is used to further remove fine oil stains and impurities, improving surface cleanliness.
Annealing:
Cold-rolled substrates are heated in a continuous annealing furnace (700-900°C) to eliminate rolling stress and improve the steel plate's plasticity. Simultaneously, in a reducing atmosphere (such as nitrogen + hydrogen), any remaining trace oxide film on the surface is reduced to metallic iron, strengthening the bond with the zinc coating. If the surface quality of the hot-rolled substrate is good, the annealing step can be simplified or only low-temperature preheating can be performed.

3. Hot-Dip Galvanizing: Forming the Zinc Layer

The pre-treated steel sheet enters the galvanizing process. The core process involves immersing the steel sheet in molten zinc, where a strong zinc layer is formed through an iron-zinc reaction.

Zinc Pot Dipping: The steel sheet is continuously immersed in a zinc pot filled with molten zinc (temperature approximately 450°C). Zinc atoms in the zinc bath diffuse and react with iron atoms on the steel sheet's surface, forming a three-layer zinc layer:

Bottom Layer: Iron-Zinc Alloy Layer (e.g., ζ and δ phases), which is tightly bonded to the substrate and determines the zinc layer's adhesion;

Middle Layer: Zinc-Iron Alloy Layer (η phase);

Surface Layer: Pure Zinc Layer (η phase), which provides primary corrosion protection. Zinc Coating Control: An air knife (a high-speed jet of nitrogen or air) is used to blow the steel sheet surface to control the zinc coating thickness (SGCC zinc coating thickness is typically Z100-Z275, or 100-275g per square meter) and ensure uniformity.

IV. Post-Processing: Improving Performance and Appearance

Cooling: The galvanized steel sheet is water- or air-cooled to room temperature to prevent the zinc layer from discoloring due to high-temperature oxidation and stabilize the zinc layer structure.

Passivation: A passivation film (such as chromate passivation or chromium-free passivation) is formed on the zinc layer surface to isolate air and moisture, delay the formation of white rust (zinc oxide, zinc hydroxide), and improve corrosion resistance.

Oil Coating (Optional): For products requiring short-term rust protection or subsequent processing (such as stamping), a thin layer of anti-rust oil is applied to the surface to reduce rust during storage.

Finishing: The steel sheet is straightened using a straightening machine and cut into fixed lengths (such as coils or flat sheets). After passing the final inspection, it is stored. Process Features: SGCC utilizes a continuous hot-dip galvanizing process, resulting in high production efficiency, a uniform zinc coating, and strong adhesion, making it suitable for large-scale industrial production. The core of this process involves pre-treatment to ensure substrate cleanliness, annealing and reduction to ensure an active surface, and controlled zinc coating structure through dip galvanizing. The result is a galvanized steel sheet that is both corrosion-resistant and versatile, meeting the fundamental needs of construction, home appliances, and industry.