What Is a CRC Low-Carbon Steel Coil?
A CRC coil is a cold-rolled carbon steel coil: hot-rolled strip is pickled to remove scale, cold-rolled to the target gauge at ambient temperature, annealed to restore ductility and then temper-rolled or skin-passed for flatness and surface finish. The result is a smooth, dimensionally accurate sheet with good surface quality, ideal for painting, plating and cold forming. Low-carbon CRC coils in the Q235, Q275 and Q345 families are widely used for stampings, housings, trays, brackets and light structures.
Grade Comparison: Q235, Q275 and Q345
Q235 and Q275 are carbon structural steels defined in GB/T 700, while Q345 is a low-alloy high-strength structural steel defined in GB/T 1591. The table below summarizes their guaranteed mechanical properties for thickness up to 16 mm.
| Grade | Standard | Yield strength (min, MPa) | Tensile strength (MPa) | Elongation (min, %) | Typical use |
|---|---|---|---|---|---|
| Q235 | GB/T 700 | 235 | 370-500 | 26 | General structures, housings, brackets |
| Q275 | GB/T 700 | 275 | 410-540 | 22 | Stronger frames, supports, machinery parts |
| Q345 | GB/T 1591 | 345 | 470-630 | 21 | Load-bearing structures, bridges, heavy machinery |
Note that elongation values are gauge-dependent and the figures above represent the minimum for the most common thickness ranges in each standard. For coils supplied with specific gauges such as 2.0 mm or 3.0 mm, the mill certificate states the exact guaranteed values.
International Equivalents
Q235B is commonly compared with St37-2 (the former DIN 17100 designation, now covered by EN 10025 S235JR) and with ASTM A36 in structural service. Q275 sits between St44 and St52 in the old DIN system and is often matched with S275JR in EN 10025. Q345 corresponds broadly to S355JR and to ASTM A572 Grade 50 in terms of strength level, although each standard differs in composition limits, impact testing and tolerances. Equivalents should always be confirmed against the applicable standard and the actual service requirements, and the mill certificate of the coil remains the authoritative document.
Applications of CRC Low-Carbon Coils
Q235 CRC coils are used for hardware stampings, appliance housings, door and window accessories, instrument enclosures, furniture parts and light structural profiles. Q275 coils are chosen where the part needs higher strength without moving to a low-alloy grade, such as machine guards, pallet racks and agricultural equipment. Q345 CRC coils are used for medium-strength load-bearing stampings and structural components, and are also common in cold-rolled form for vehicle components and machinery frames.
Surface and Delivery Conditions
CRC coils are delivered with an oiled or dry surface, as specified. The light rust-preventive oil protects the surface during transport and storage and must be degreased before painting or plating. Surface quality follows the applicable product standard, with limits on scratches, dents and stains. For coated applications, the coil can be supplied to a surface class suitable for painting or for subsequent hot-dip galvanizing, electro-galvanizing or coil coating.
Corrosion Protection and Maintenance
Bare carbon steel has no inherent corrosion resistance. In dry indoor environments it can be used as delivered with an oil film, but in humid or outdoor service it must be painted, plated or galvanized. Hot-dip galvanizing is the most common protection for structural parts, and electro-galvanizing or coil coating for smaller stamped components. If the part will be exposed to aggressive disinfectants or chemicals, carbon steel should be replaced by a stainless grade rather than protected by coatings alone.
Buying Checklist
When purchasing Q235, Q275 or Q345 CRC coils, request the mill certificate showing grade, chemical composition, mechanical properties, delivery condition, heat number and applicable standard, and verify that the heat number matches the coil delivered. Confirm the gauge, width, surface finish (bright or matte), oiling condition, and the thickness tolerance class. Agree on the test methods, such as tensile testing per the applicable standard, before shipment.
FAQ
What does CRC mean in steel coil naming?
CRC stands for cold-rolled coil. The steel is rolled at ambient temperature after pickling, then annealed and temper-rolled, which gives a smooth surface and accurate dimensions compared with hot-rolled coil.
What is the difference between Q235 and Q345?
Q235 is a carbon structural steel with 235 MPa minimum yield, while Q345 is a low-alloy high-strength steel with 345 MPa minimum yield. Q345 costs more but supports higher loads with the same section size.
Is Q235 the same as St37?
Q235B is frequently treated as equivalent to St37-2 or S235JR at the same strength level, but the grades belong to different standards with different composition and impact requirements. Confirm the applicable standard and certificate before substitution.
Can Q235 cold-rolled coil be used in humid environments?
Only with proper protection. Bare Q235 rusts quickly when wet. Paint, electro-galvanize or hot-dip galvanize the part for humid service, and select a stainless grade if aggressive chemicals are present.
What surface conditions are available for CRC coils?
Coils can be supplied oiled or dry, and with bright or matte finish, depending on the product standard and the customer's processing needs. The finish class should be stated in the order.
Which grade should I choose for stamped machine housings?
Q235 is the usual choice for general housings and enclosures because it is economical and easy to form. Move to Q275 or Q345 when the part carries higher loads or needs better dent resistance.

