What effects does cold working have on the physical properties of Q195 material?

Aug 18, 2025 Leave a message

Cold working (such as cold rolling, cold drawing, cold bending, and stamping) applies external forces to Q195, causing plastic deformation and significantly altering its physical properties. These changes primarily stem from adjustments to the material's internal structure (such as grain deformation and increased dislocation density). The specific effects are as follows:
1. Changes in Mechanical Properties (Most Significant Impact)
Increased Strength and Hardness (Work Hardening)
During cold working, the material's internal grains are elongated and flattened (forming a "fibrous structure"). Simultaneously, dislocations (crystal defects) proliferate and entangle with each other, hindering further atomic slip and enhancing the material's resistance to deformation.
This manifests as significant increases in tensile strength (σb) and yield strength (σs), as well as an increase in hardness (e.g., Brinell hardness HB). For example, the tensile strength of Q195 in the annealed state is approximately 315-430 MPa. After 50% cold deformation, the tensile strength rises to 500-600 MPa, and the hardness increases by 30%-50%. Decreased Plasticity and Toughness
As the amount of deformation increases, stress concentration within the material intensifies. Grain fragmentation and dislocation accumulation make further plastic deformation difficult, resulting in a significant decrease in elongation (δ) and reduction of area (ψ).
For example, the elongation of annealed Q195 is approximately 30%-40%. After cold working to a deformation of 30%, this elongation may drop to 10%-15%, and fracture is more likely to be brittle (without significant plastic deformation).

Slightly Reduced Elastic Modulus
Cold working causes lattice distortion, which affects interatomic bonding, resulting in a slight decrease in the material's elastic modulus (E) (typically 5%-10%). However, this effect is far less significant than the changes in strength and plasticity.

II. Other Changes in Physical Properties
Slightly Reduced Density
During cold working, plastic deformation may create microscopic pores or microcracks within the material, leading to a slight decrease in overall density (typically <1%). However, this has a negligible impact on macroscopic performance. Reduced Electrical and Thermal Conductivity
Q195, as a low-carbon steel, has electrical and thermal conductivity primarily determined by the crystal structure of the iron matrix. Cold working causes grain distortion and increased dislocations, hindering the directional movement of free electrons, resulting in a decrease in electrical and thermal conductivity (approximately 5%-15%), but still far less than the changes seen in non-ferrous metals such as copper and aluminum.
Magnetic Changes
Q195 is a ferromagnetic material. Cold working causes the grains to become more uniform (fibrous), resulting in anisotropic magnetic permeability (the material's ability to conduct magnetic fields): slightly higher permeability along the deformation direction and slightly lower perpendicularly, but the overall magnetic properties (such as saturation magnetic induction intensity) remain largely unchanged.
Dimensional and Shape Stability
Cold working can leave "internal stresses" within the material (such as residual stress after cold rolling). Subsequent changes in ambient temperature or external forces can cause slight "springback" or dimensional changes (such as a slight angulation of a cold-bent part after storage), affecting dimensional accuracy. III. Relationship between the Degree of Impact and the Amount of Deformation
The degree of impact of cold working on the physical properties of Q195 is positively correlated with the amount of deformation (processing rate):
When the deformation is less than 10%, the performance changes are relatively gradual, with a slight increase in strength and a minimal decrease in ductility. This makes it suitable for applications requiring high ductility (such as light bending).
When the deformation is between 10% and 50%, work hardening is significant, with a rapid increase in strength and hardness and a sharp decrease in ductility. This makes it suitable for parts requiring high strength (such as cold-drawn steel wire and cold-rolled sheet).
When the deformation is greater than 50%, the material approaches a "cold brittle" state and is prone to cracking during processing. Intermediate annealing is required to eliminate work hardening before further processing.
Summary
The core impact of cold working on Q195 is the work hardening effect of "increased strength and decreased ductility," accompanied by a slight deterioration in physical properties such as electrical and thermal conductivity, as well as dimensional stability issues caused by internal stresses. These changes can be partially eliminated by subsequent heat treatment (such as annealing) (restoring plasticity and reducing internal stress). Therefore, in practical applications, it is necessary to balance the cold working deformation and performance requirements according to needs, and adjust the performance in combination with heat treatment process when necessary.